Schwinn 425 Elliptical Assembly and Owner's Manual - Page 27

Console Setup Mode

Page 27 highlights

CONSOLE SETUP MODE The Console Setup Mode lets you set the units of measure to either English or Metric, change the machine type, or see maintenance statistics (Error Log and Run Hours - for service technician use only). 1. Hold down the Increase button and Decrease button together for 3 seconds while in the Power-Up Mode to go into the Console Setup Mode. Note: Push START/STOP to go back to the previous screen or the Power-Up Mode screen. 2. The Console display shows the Units prompt. Push ENTER to start Units option. Push the Increase/Decrease buttons to change between "Miles-Lb" (English units) and "Km-Kg" (metric units). Note: If the units change when there is data in User Statistics, the statistics change to the new units. 3. Push ENTER to set. For the next option, push the Increase button. 4. The Console display shows the Machine Type prompt. Push ENTER to start Machine Type option. Push the Increase/ Decrease buttons to change between ELLIPTICAL and BIKE. 5. Push ENTER to set. For the next option, push the Increase button. 6. The Console display shows the Error Log prompt. Push ENTER to start Error Log option. The Error Log stores the last 10 errors (error type and system time of error), listed newest to oldest. Push the Increase/Decrease buttons to move through the Error Log. If there are no errors, the Console display shows "Index=0". 7. Push START/STOP to exit. For the next option, push the Increase button. 8. The Console shows the Run Hours prompt. Push ENTER to see total hours for the machine. 9. Push START/STOP to exit. For the next option, push the Increase button. 10. The Console display shows the Units prompt again. Push START/STOP to go back to the Power-Up Mode screen. 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34

27
CONSOLE SETUP MODE
The Console Setup Mode lets you set the units of measure to either English or Metric, change the machine type, or see
maintenance statistics (Error Log and Run Hours – for service technician use only).
1.
Hold down the Increase button and Decrease button together for 3 seconds while in the Power-Up Mode to go into
the Console Setup Mode.
Note:
Push START/STOP to go back to the previous screen or the Power-Up Mode screen.
2.
The Console display shows the Units prompt. Push ENTER to start Units option. Push the Increase/Decrease
buttons to change between “Miles-Lb” (English units) and “Km-Kg” (metric units).
Note:
If the units change when there is data in User Statistics, the statistics change to the new units.
3.
Push ENTER to set. For the next option, push the Increase button.
4.
The Console display shows the Machine Type prompt. Push ENTER to start Machine Type option. Push the Increase/
Decrease buttons to change between ELLIPTICAL and BIKE.
5.
Push ENTER to set. For the next option, push the Increase button.
6.
The Console display shows the Error Log prompt. Push ENTER to start Error Log option. The Error Log stores the
last 10 errors (error type and system time of error), listed newest to oldest. Push the Increase/Decrease buttons to
move through the Error Log. If there are no errors, the Console display shows “Index=0”.
7.
Push START/STOP to exit. For the next option, push the Increase button.
8.
The Console shows the Run Hours prompt. Push ENTER to see total hours for the machine.
9.
Push START/STOP to exit. For the next option, push the Increase button.
10.
The Console display shows the Units prompt again. Push START/STOP to go back to the Power-Up Mode screen.