Home » Seagate Manuals » Hard Drives » Seagate Enterprise Capacity 3.5 HDD/Constellation ES » Manual Viewer

Seagate Enterprise Capacity 3.5 HDD/Constellation ES Constellation ES (.1) SAS - Page 48

KxX=F, < 15lb = 67N

View all Seagate Enterprise Capacity 3.5 HDD/Constellation ES manuals

Add to My Manuals
Save this manual to your list of manuals

Page 48 highlights

If forced air is determined to be necessary, possible air-flow patterns are shown in Figure 15. The air-flow patterns are created by one or more fans, either forcing or drawing air as shown in the illustrations. Conduction, convection, or other forced air-flow patterns are acceptable as long as the temperature measurement guidelines of Section 6.5.1 are met. b Note. l b b b Note. l Figure 15. Air flow 10.3 DRIVE MOUNTING Mount the drive using the bottom or side mounting holes. If you mount the drive using the bottom holes, ensure that you do not physically distort the drive by attempting to mount it on a stiff, non-flat surface. The allowable mounting surface stiffness is 80 lb/in (14.0 N/mm). The following equation and paragraph define the allowable mounting surface stiffness: K x X = F < 15lb = 67N where K is the mounting surface stiffness (units in lb/in or N/mm) and X is the out-of-plane surface distortion (units in inches or millimeters). The out-of-plane distortion (X) is determined by defining a plane with three of the four mounting points fixed and evaluating the out-of-plane deflection of the fourth mounting point when a known force (F) is applied to the fourth point. 10.4 GROUNDING Signal ground (PCBA) and HDA ground are connected together in the drive and cannot be separated by the user. The equipment in which the drive is mounted is connected directly to the HDA and PCBA with no electrically isolating shock mounts. If it is desired for the system chassis to not be connected to the HDA/PCBA ground, the systems integrator or user must provide a nonconductive (electrically isolating) method of mounting the drive in the host equipment. Increased radiated emissions may result if you do not provide the maximum surface area ground connection between system ground and drive ground. This is the system designer's and integrator's responsibility. CONSTELLATION ES.1 SAS PRODUCT MANUAL, REV. G 42

Section	Page
Constellation® ES.1 SAS	1
Seagate® Technology Support Services	7
1.0 Scope	8
2.0 Applicable standards and reference documentation	9
2.1 Standards	9
2.1.1 Electromagnetic compatibility	9
2.1.2 Electromagnetic compliance	9
2.1.3 European Union Restriction of Hazardous Substances (RoHS)	10
2.1.4 China Restriction of Hazardous Substances (RoHS) Directive	10
2.2 Reference documents	11
3.0 General description	12
3.1 Standard features	13
3.2 Media description	13
3.3 Performance	14
3.4 Reliability	14
3.5 Formatted capacities	14
3.6 Programmable drive capacity	14
3.7 Factory-installed options	14
4.0 Performance characteristics	15
4.1 Internal drive characteristics	15
4.2 Seek performance characteristics	15
4.2.1 Access time	15
4.2.2 Format command execution time for 512-byte sectors (minutes)	15
4.2.3 General performance characteristics	16
4.3 Start/stop time	16
4.4 Prefetch/multi-segmented cache control	16
4.5 Cache operation	16
4.5.1 Caching write data	17
4.5.2 Prefetch operation	17
5.0 Reliability specifications	18
5.1 Error rates	18
5.1.1 Recoverable Errors	18
5.1.2 Unrecoverable Errors	18
5.1.3 Seek errors	18
5.1.4 Interface errors	18
5.2 Reliability and service	19
5.2.1 Annualized Failure Rate (AFR) and Mean Time Between Failure (MTBF)	19
5.2.2 Preventive maintenance	19
5.2.3 Hot plugging the drive	19
5.2.4 S.M.A.R.T.	20
5.2.5 Thermal monitor	21
5.2.6 Drive Self Test (DST)	21
5.2.7 Product warranty	23
6.0 Physical/electrical specifications	24
6.1 PowerChoiceTM power management	24
6.1.1 PowerChoice reporting methods	24
6.2 AC power requirements	25
6.3 DC power requirements	25
6.3.1 Conducted noise immunity	28
6.3.2 Power sequencing	28
6.3.3 Current profiles	28
6.4 Power dissipation	31
6.5 Environmental limits	37
6.5.1 Temperature	37
6.5.2 Relative humidity	37
6.5.3 Effective altitude (sea level)	37
6.5.4 Shock and vibration	37
6.5.5 Acoustics	39
6.5.6 Air cleanliness	39
6.5.7 Corrosive environment	39
6.5.8 Electromagnetic susceptibility	39
6.6 Mechanical specifications	40
7.0 About FIPS	41
8.0 About self-encrypting drives	42
8.1 Data encryption	42
8.2 Controlled access	42
8.2.1 Admin SP	42
8.2.2 Locking SP	42
8.2.3 Default password	42
8.3 Random number generator (RNG)	42
8.4 Drive locking	42
8.5 Data bands	43
8.6 Cryptographic erase	43
8.7 Authenticated firmware download	43
8.8 Power requirements	43
8.9 Supported commands	43
8.10 Sanitize - CRYPTOGRAPHIC ERASE	43
8.11 RevertSP	43
9.0 Defect and error management	44
9.1 Drive internal defects/errors	44
9.2 Drive error recovery procedures	44
9.3 SAS system errors	45
9.4 Background Media Scan	45
9.5 Media Pre-Scan	45
9.6 Deferred Auto-Reallocation	46
9.7 Idle Read After Write	46
9.8 Protection Information (PI)	46
9.8.1 Levels of PI	46
9.8.2 Setting and determining the current Type Level	46
9.8.3 Identifying a Protection Information drive	46
10.0 Installation	47
10.1 Drive orientation	47
10.2 Cooling	47
10.3 Drive mounting	48
10.4 Grounding	48
11.0 Interface requirements	49
11.1 SAS features	49
11.1.1 task management functions	49
11.1.2 task management responses	49
11.2 Dual port support	49
11.3 SCSI commands supported	50
11.3.1 Inquiry data	54
11.3.2 Mode Sense data	55
11.4 Miscellaneous operating features and conditions	59
11.4.1 SAS physical interface	59
11.4.2 Physical characteristics	62
11.4.3 Connector requirements	62
11.4.4 Electrical description	62
11.4.5 Pin descriptions	62
11.4.6 SAS transmitters and receivers	63
11.4.7 Power	63
11.5 Signal characteristics	63
11.5.1 Ready LED Out	63
11.5.2 Differential signals	64
11.6 SAS-2 Specification Compliance	64
11.7 Additional information	64
Numerics	65
A	65
B	65
C	65
D	65
E	66
F	66
G	66
H	66
I	66
J	66
K	66
L	66
M	66
N	67
O	67
P	67
Q	67
R	67
S	68
T	68
U	68
V	68
W	68

Match case Limit results 1 per page

ONSTELLATION

ES.1 SAS P

RODUCT

ANUAL

, R

. G

If forced air is determined to be necessary, possible air-flow patterns are shown in Figure 15. The air-flow patterns are created by one or

more fans, either forcing or drawing air as shown in the illustrations. Conduction, convection, or other forced air-flow patterns are

acceptable as long as the temperature measurement guidelines of Section 6.5.1 are met.

Figure 15.

Air flow

10.3

RIVE MOUNTING

Mount the drive using the bottom or side mounting holes. If you mount the drive using the bottom holes, ensure that you do not physically

distort the drive by attempting to mount it on a stiff, non-flat surface.

The allowable mounting surface stiffness is 80 lb/in (14.0 N/mm). The following equation and paragraph define the allowable mounting

surface stiffness:

where K is the mounting surface stiffness (units in lb/in or N/mm) and X is the out-of-plane surface distortion (units in inches or millimeters).

The out-of-plane distortion (X) is determined by defining a plane with three of the four mounting points fixed and evaluating the out-of-plane

deflection of the fourth mounting point when a known force (F) is applied to the fourth point.

10.4

ROUNDING

Signal ground (PCBA) and HDA ground are connected together in the drive and cannot be separated by the user. The equipment in which

the drive is mounted is connected directly to the HDA and PCBA with no electrically isolating shock mounts. If it is desired for the system

chassis to not be connected to the HDA/PCBA ground, the systems integrator or user must provide a nonconductive (electrically isolating)

method of mounting the drive in the host equipment.

Increased radiated emissions may result if you do not provide the maximum surface area ground connection between system ground and

drive ground. This is the system designer’s and integrator’s responsibility.

Note.

KxX=F

< 15lb = 67N