Home » Seagate Manuals » Hard Drives » Seagate ST160LT007 » Manual Viewer

Seagate ST160LT007 Momentus Thin (.2-4K) SATA Product Manual - Page 1

Seagate ST160LT007 Manual

Add to My Manuals
Save this manual to your list of manuals

Page 1 highlights

Product Manual Momentus® Thin 7200-RPM ST model # - Part # Standard models ST320LT007 - 9ZV142 ST250LT007 - 9ZV14C ST160LT007 - 9ZV14D Free-Fall Sensor models ST320LT011 - 9ZVG42 ST250LT011 - 9ZVG4C ST160LT011 - 9ZVG4D ST model # - Part # SED model ST320LT014 - 9YK142 ST250LT014 - 9YK14C ST160LT014 - 9YK14D SED (FIPS 140-2) models ST320LT009 - 9WC142 ST250LT009 - 9WC14C ST160LT009 - 9WC14D Gen-2 100625253 Rev. D March 2011

Section	Page
1.0 Seagate Technology support services	7
2.0 Introduction	8
2.1 About the Serial ATA interface	9
3.0 Drive specifications	10
3.1 Specification summary table	10
3.2 Formatted capacity	12
3.2.1 LBA mode	12
3.3 Default logical geometry	12
3.4 Physical organization	12
3.5 Recording and interface technology	13
3.6 Physical characteristics	13
3.7 Seek time	13
3.8 Start/stop times	14
3.9 Power specifications	14
3.9.1 Power consumption	14
3.9.1.1 Typical current profile	16
3.9.2 Deferred spinup	16
3.9.3 Conducted noise	16
3.9.4 Voltage tolerance	16
3.9.5 Power-management modes	17
3.10 Environmental specifications	18
3.10.1 Ambient temperature	18
3.10.2 Temperature gradient	18
3.10.3 Humidity	18
3.10.3.1 Relative humidity	18
3.10.3.2 Wet bulb temperature	18
3.10.4 Altitude	18
3.10.5 Shock	19
3.10.5.1 Operating shock	19
3.10.5.2 Nonoperating shock	19
3.10.6 Vibration	19
3.10.6.1 Operating vibration	19
3.10.6.2 Nonoperating vibration	19
3.11 Acoustics	20
3.12 Electromagnetic immunity	20
3.13 Reliability	21
3.14 Agency certification	21
3.14.1 Safety certification	21
3.14.2 Electromagnetic compatibility	21
3.14.3 FCC verification	22
3.15 Environmental protection	23
3.15.1 European Union Restriction of Hazardous Substances (RoHS)	23
3.15.2 China Restriction of Hazardous Substances (RoHS) Directive	23
3.16 Corrosive environment	23
4.0 Configuring and mounting the drive	24
4.1 Handling and static-discharge precautions	24
4.2 Configuring the drive	24
4.3 Serial ATA cables and connectors	25
4.4 Drive mounting	25
5.0 About FIPS	28
6.0 Serial ATA (SATA) interface	30
6.1 Hot-Plug compatibility	30
6.2 Serial ATA device plug connector pin definitions	30
6.3 Supported ATA commands	32
6.3.1 Identify Device command	34
6.3.2 Set Features command	38
6.3.3 S.M.A.R.T. commands	39
Index	41
A	41
B	41
C	41
D	41
E	41
F	41
G	41
H	42
I	42
K	42
L	42
M	42
N	42
O	42
P	42
Q	42
R	42
S	43
T	43
U	43
V	43