Home » Seagate Manuals » Hard Drives » Seagate ST160LT007 » Manual Viewer

Seagate ST160LT007 Momentus Thin (.2-4K) SATA Product Manual - Page 31

Notes, Table 7, Serial ATA connector pin definitions

Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

Table 7: Serial ATA connector pin definitions Segment Pin P1 P2 P3 P4 P5 P6 P7 P8 Power P9 P10 P11 P12 P13 P14 P15 Function V33 V33 V33 Ground Ground Ground V5 V5 V5 Ground Reserved Ground V12 V12 V12 Definition 3.3V power 3.3V power 3.3V power, pre-charge, 2nd mate 1st mate 2nd mate 2nd mate 5V power, pre-charge, 2nd mate 5V power 5V power 2nd mate The pin corresponding to P11 in the backplane receptacle connector is also reserved The corresponding pin to be mated with P11 in the power cable receptacle connector shall always be grounded 1st mate. 12V power, pre-charge, 2nd mate 12V power 12V power Notes: 1. All pins are in a single row, with a 1.27 mm (0.050") pitch. 2. The comments on the mating sequence apply to the case of backplane blindmate connector only. In this case, the mating sequences are: • the ground pins P4 and P12. • the pre-charge power pins and the other ground pins. • the signal pins and the rest of the power pins. 3. There are three power pins for each voltage. One pin from each voltage is used for pre-charge when installed in a blind-mate backplane configuration. 4. All used voltage pins (Vx) must be terminated. Momentus Thin Product Manual, Gen-2 Rev. D 25

Section	Page
1.0 Seagate Technology support services	7
2.0 Introduction	8
2.1 About the Serial ATA interface	9
3.0 Drive specifications	10
3.1 Specification summary table	10
3.2 Formatted capacity	12
3.2.1 LBA mode	12
3.3 Default logical geometry	12
3.4 Physical organization	12
3.5 Recording and interface technology	13
3.6 Physical characteristics	13
3.7 Seek time	13
3.8 Start/stop times	14
3.9 Power specifications	14
3.9.1 Power consumption	14
3.9.1.1 Typical current profile	16
3.9.2 Deferred spinup	16
3.9.3 Conducted noise	16
3.9.4 Voltage tolerance	16
3.9.5 Power-management modes	17
3.10 Environmental specifications	18
3.10.1 Ambient temperature	18
3.10.2 Temperature gradient	18
3.10.3 Humidity	18
3.10.3.1 Relative humidity	18
3.10.3.2 Wet bulb temperature	18
3.10.4 Altitude	18
3.10.5 Shock	19
3.10.5.1 Operating shock	19
3.10.5.2 Nonoperating shock	19
3.10.6 Vibration	19
3.10.6.1 Operating vibration	19
3.10.6.2 Nonoperating vibration	19
3.11 Acoustics	20
3.12 Electromagnetic immunity	20
3.13 Reliability	21
3.14 Agency certification	21
3.14.1 Safety certification	21
3.14.2 Electromagnetic compatibility	21
3.14.3 FCC verification	22
3.15 Environmental protection	23
3.15.1 European Union Restriction of Hazardous Substances (RoHS)	23
3.15.2 China Restriction of Hazardous Substances (RoHS) Directive	23
3.16 Corrosive environment	23
4.0 Configuring and mounting the drive	24
4.1 Handling and static-discharge precautions	24
4.2 Configuring the drive	24
4.3 Serial ATA cables and connectors	25
4.4 Drive mounting	25
5.0 About FIPS	28
6.0 Serial ATA (SATA) interface	30
6.1 Hot-Plug compatibility	30
6.2 Serial ATA device plug connector pin definitions	30
6.3 Supported ATA commands	32
6.3.1 Identify Device command	34
6.3.2 Set Features command	38
6.3.3 S.M.A.R.T. commands	39
Index	41
A	41
B	41
C	41
D	41
E	41
F	41
G	41
H	42
I	42
K	42
L	42
M	42
N	42
O	42
P	42
Q	42
R	42
S	43
T	43
U	43
V	43