Sharp DT 100 DT-100 Operation Manual

Sharp DT 100 - WVGA DLP Projector Manual

Get Sharp DT 100 - WVGA DLP Projector PDF manuals and user guides
UPC - 074000364684
View all Sharp DT 100 manuals
Add to My Manuals
Save this manual to your list of manuals

Sharp DT 100 manual content summary:

  • Sharp DT 100 | DT-100 Operation Manual - Page 1
    PROJECTOR PROJECTEUR PROYECTOR DT-100 OPERATION MANUAL MODE D'EMPLOI MANUAL DE MANEJO ESPAÑOL FRANÇAIS ENGLISH
  • Sharp DT 100 | DT-100 Operation Manual - Page 2
    DT-100 Serial No.: There are two important reasons for prompt warranty registration of your new SHARP Projector, using the REGISTRATION CARD packed with the projector. 1. WARRANTY This is to assure that you immediately receive the full benefit of the parts, service (servicing) instructions in
  • Sharp DT 100 | DT-100 Operation Manual - Page 3
    remote control. Ensure the cooling fan has stopped before disconnecting the power cord. DURING NORMAL OPERATION, NEVER TURN THE PROJECTOR OFF BY DISCONNECTING THE POWER CORD. FAILURE TO OBSERVE THIS WILL RESULT IN PREMATURE LAMP conformity SHARP PROJECTOR, MODEL DT-100 This device complies with Part
  • Sharp DT 100 | DT-100 Operation Manual - Page 4
    • In this operation manual, the illustration and the Bright Color Tint Sharp CLR Temp Bright Boost Progressive Lamp Setting Reset SEL./ projector. Note .........Indicates additional information for setting up and operating the projector. For Future Reference Maintenance P. 47 Troubleshooting
  • Sharp DT 100 | DT-100 Operation Manual - Page 5
    Adjusting the Projector Function ("PRJ - ADJ" menu 44 Auto Search Function 44 Auto Sync (Auto Sync Adjustment) ..... 44 Auto Power Off Function 45 Setting the Confirmation Sound (System Sound 45 Speaker Setting 45 Fan Mode Setting 45 Checking the Lamp Life Status 45 Troubleshooting with "Help
  • Sharp DT 100 | DT-100 Operation Manual - Page 6
    Maintenance Indicators 48 Regarding the Lamp 50 Lamp 50 Caution Concerning the Lamp 50 Replacing the Lamp 50 Removing and Installing the Lamp Unit 51 Resetting the Lamp Timer 52 Connecting Pin Assignments 53 Computer Compatibility Chart 54 Troubleshooting 55 Service Information (For the
  • Sharp DT 100 | DT-100 Operation Manual - Page 7
    engineered and manufactured to assure your personal safety. BUT IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARDS. In order not to defeat the safeguards incorporated in this product, observe the following basic rules for its installation, use and servicing. 1. Read Instructions
  • Sharp DT 100 | DT-100 Operation Manual - Page 8
    , be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards. 20. Safety Check Upon completion of any service or repairs to this product
  • Sharp DT 100 | DT-100 Operation Manual - Page 9
    hazard of glass par- ticles if lamp ruptures. In case of lamp rupture, contact your nearest Sharp Authorized Service Center or Dealer for replacement. See "Replacing the Lamp" on page 50. Caution concerning the setup of the projector I For minimal servicing and to maintain high image quality
  • Sharp DT 100 | DT-100 Operation Manual - Page 10
    and turning off the equipment to be connected. I Please read the operation manuals of the projector and the equipment to be connected for instructions on how to make the connections. Using the projector in other countries I The power supply voltage and the shape of the plug may vary depending on
  • Sharp DT 100 | DT-100 Operation Manual - Page 11
    • Operation manual (this manual (TINS-B999WJZZ)) Power cord for U.S. and Canada, etc. (6' (1.8 m)) QACCDA007WJPZ Optional accessory I Lamp unit AN-100LP Note • This optional accessory may not be available depending on the region. Please check with your nearest Sharp Authorized Service Center or
  • Sharp DT 100 | DT-100 Operation Manual - Page 12
    Part Names and Functions Numbers in Z refer to the main pages in this operation manual where the topic is explained. Projector Top View Power indicator 28, 48 STANDBY/ON 28 button For turning the power on and putting the projector . 15 Remote control sensor Push both sides of the lens cap to
  • Sharp DT 100 | DT-100 Operation Manual - Page 13
    Part Names and Functions (Continued) Numbers in Z refer to the main pages in this operation manual where the topic is explained. Rear View 47 Exhaust vent Intake vent 47 AC socket 28 Connect the supplied Power instructions on how to use it to secure the projector an audio cable (commercially
  • Sharp DT 100 | DT-100 Operation Manual - Page 14
    refer to the main pages in this operation manual where the topic is explained. STANDBY button 29 For putting the projector into the standby button For selecting the appropriate picture. 28 ON button For turning the power on. 39 MENU/HELP button For displaying adjustment 46 and setting screens,
  • Sharp DT 100 | DT-100 Operation Manual - Page 15
    Part Names and Functions (Continued) Inserting the Batteries 1 Press the P mark on included with this projector may run down in a short period, depending on how they are kept. Be sure to replace them as soon as possible with new batteries. • Remove the batteries from the remote control if you
  • Sharp DT 100 | DT-100 Operation Manual - Page 16
    • Ensure that you do not drop, expose to mois- ture or high temperature. • The remote control may malfunction under a fluorescent lamp. In this case, move the projector away from the fluorescent lamp. 30° Remote control signal transmitters 30° Remote control sensor 23n (7 m) Remote control 15
  • Sharp DT 100 | DT-100 Operation Manual - Page 17
    a screen _P. 18 2. Connect the projector to the video equipment and plug the power cord into the AC socket of the projector To AUDIO (INPUT 3, 4) terminal AC socket To INPUT 3 terminal _PP. 22-28 3. Remove the lens cap and turn the projector on On the projector On the remote control _P. 28 16
  • Sharp DT 100 | DT-100 Operation Manual - Page 18
    trapezoidal distortion using the Keystone Correction. On the projector Shrinks upper side. On the remote control _PP. 30, 31 Shrinks lower side. _P. 33 8. Turn the Power off Press the STANDBY/ON button on the projector or the STANDBY button on the remote control, and then press the button again
  • Sharp DT 100 | DT-100 Operation Manual - Page 19
    concerning "Screen Size and Projection Distance". Ceiling-mount Setup I It is recommended that you use the optional Sharp ceiling-mount bracket for this installation. Before mounting the projector, contact your nearest Sharp Authorized Service Center or Dealer to obtain the recommended ceiling
  • Sharp DT 100 | DT-100 Operation Manual - Page 20
    (PRJ) Mode The projector can use any of the 4 projection modes, shown in the diagram below. Select the mode most appropriate for the projection setting in use. (You can set the PRJ mode in "SCR-ADJ" menu. See page 43.) I Table mounted, front projection I Ceiling mounted, front projection Setup
  • Sharp DT 100 | DT-100 Operation Manual - Page 21
    Setting up the Projector (Continued) Screen Size and Projection Distance When using a wide screen (16:9) and cm) 200Љ (508 cm) 150Љ (381 cm) 160Љ (406 cm) 120Љ (305 cm) 120Љ (305 cm) 90Љ (229 cm) 100Љ (254 cm) 80Љ (203 cm) 60Љ (152 cm) 80Љ (203 cm) 64Љ (163 cm) 48Љ (122 cm) 70Љ (178
  • Sharp DT 100 | DT-100 Operation Manual - Page 22
    cm) 200Љ (508 cm) 150Љ (381 cm) 200Љ (508 cm) 160Љ (406 cm) 120Љ (305 cm) 150Љ (381 cm) 120Љ (305 cm) 90Љ (229 cm) 100Љ (254 cm) 80Љ (203 cm) 60Љ (152 cm) 80Љ (203 cm) 64Љ (163 cm) 48Љ (122 cm) 70Љ (178 cm) 56Љ (142 cm) 42Љ (107
  • Sharp DT 100 | DT-100 Operation Manual - Page 23
    of connection and cables, refer to the operation manual of the connecting equipment. • You may need other cables or connectors not listed below. Equipment Input Signal Cable Terminal on the projector Audio-visual equipment Component video Component cable (commercially available) INPUT1
  • Sharp DT 100 | DT-100 Operation Manual - Page 24
    connecting, ensure that the power cord of the projector is unplugged from the AC outlet and turn off the devices to be connected. After making all connections, turn on the projector first and then the other devices. The projector is equipped with input terminals that support component, S-video, and
  • Sharp DT 100 | DT-100 Operation Manual - Page 25
    output terminal To INPUT3 terminal To AUDIO (INPUT3, 4) terminal L R RCA audio cable* (commercially available) *Use the cable when you want to enjoy the sound from the projector's speaker. S-video cable (commercially available) When connecting to equipment with video output terminal (INPUT4
  • Sharp DT 100 | DT-100 Operation Manual - Page 26
    Sharp service part QCNWGA038WJPZ) RGB Cable (commercially available) * When using the ø3.5 mm mono audio cable, the volume level will be half of when using the ø3.5 mm stereo audio cable. Note • See page 54 "Computer Compatibility Chart" for a list of computer signals compatible with the projector
  • Sharp DT 100 | DT-100 Operation Manual - Page 27
    computer images on both the projector and a separate monitor using two sets of RGB cables. Computer Monitor To INPUT 1 terminal To RGB output terminal To OUTPUT (INPUT 1, 2) terminal To RGB input terminal RGB cable (commercially available) RGB cable (commercially available) Note • RGB
  • Sharp DT 100 | DT-100 Operation Manual - Page 28
    OUTPUT terminal To audio input terminal ø3.5 mm minijack to RCA audio cable (commercially available) Note • ø3.5 mm minijack to RCA audio cable (commercially available) is required. • Before connecting, ensure that both the projector and the audio equipment to be connected are turned off. • When
  • Sharp DT 100 | DT-100 Operation Manual - Page 29
    the projector or fON on the remote control. Info • English is the factory default language. If you want to change the on-screen display to another language, change the language according to the procedure on page 43. Lamp indicator Power indicator Note • About the Lamp Indicator The lamp indicator
  • Sharp DT 100 | DT-100 Operation Manual - Page 30
    /ON on the projector or eSTANDBY on the remote control, then press that button again while the confirmation message is displayed, to put the projector into standby mode. 2 Unplug the power cord from the AC outlet after the cooling fan stops. • The power indicator on the projector blinks in green
  • Sharp DT 100 | DT-100 Operation Manual - Page 31
    the appropriate input mode for the connected equipment. PressC INPUT 1, C INPUT 2, DINPUT 3 or EINPUT 4 on the remote control to select the input mode. • When pressing INPUT (P/R) on the projector, input mode switches in the following order: INPUT1 INPUT2 INPUT3 INPUT4 • When "Auto Search" is set to
  • Sharp DT 100 | DT-100 Operation Manual - Page 32
    can be adjusted using the adjustment feet at the front and rear of the projector. When the screen is above the projector, the projection image can be made higher by adjusting the projector. 1 Lift the projector to adjust its height while lifting the HEIGHT ADJUST lever. 2 Remove your hands from
  • Sharp DT 100 | DT-100 Operation Manual - Page 33
    Image Projection (Continued) Adjusting the Volume Press K/L on the remote control or -O/Q+ on the projector to adjust the volume. Note • Pressing K/-O will lower the volume. • Pressing L/Q+ will raise the volume. • When the projector is connected to external equipment, the volume level of the
  • Sharp DT 100 | DT-100 Operation Manual - Page 34
    - direction.) 3 Press g KEYSTONE. • The on-screen display of the Keystone Correction mode will disappear. • You can also use d KEYSTONE on the projector. Info • While adjusting the image using Keystone Correction, straight lines and the edges of the image may appear jagged. Basic Operation 33
  • Sharp DT 100 | DT-100 Operation Manual - Page 35
    Image Projection (Continued) Resize Mode This function allows you to modify or customize the resize mode to enhance the input image. Depending on the input signal, you can choose "STRETCH", "SIDE BAR" or "CINEMA ZOOM" image. Press HRESIZE. • See page 43 for setting on menu screen. RESIZE button
  • Sharp DT 100 | DT-100 Operation Manual - Page 36
    Computer 4:3 aspect ratio Other aspect ratios SVGA (800 K 600) XGA (1024 K 768) SXGA (1280 K 960) SXGA L (1400 K 1050) SXGA (1280 K 1024) 1280 K 720 STRETCH 854 K 480 854 K 480 854 K 480 SIDE BAR 640 K 480 640 K 480 J Input Signal Computer Image type STRETCH Output screen image SIDE BAR
  • Sharp DT 100 | DT-100 Operation Manual - Page 37
    Operating with the Remote Control Freezing a Moving Image 1 Press NFREEZE. • The projected image Sync Adjustment) Auto Sync function works when detecting input signal after the projector turns on. Press FAUTO SYNC to manually adjust with Auto Sync function. Note • When the optimum image cannot be
  • Sharp DT 100 | DT-100 Operation Manual - Page 38
    Main menu Picture Picture Mode INPUT 1 (Component)/INPUT 2 Page 41 Page 41 (Component)/INPUT 3/INPUT 4 Sub menu Standard Natural Dynamic Movie1 Movie2 Picture SCR - ADJ PRJ - ADJ Help Picture Mode Contrast Bright Color Tint Sharp CLR Temp Bright Boost Progressive Lamp Setting Reset SEL
  • Sharp DT 100 | DT-100 Operation Manual - Page 39
    Main menu PRJ - ADJ Page 44 Lamp Timer(Life) SEL./ADJ. 0h ENTER 100% END Sub menu Auto Search [On/Off] Page 44 Auto Sync [On/Off] Page 44 Auto Power appear Data image is not centered Color is faded or poor Picture is dark The image is distorted Reset all adjustments to default settings SEL.
  • Sharp DT 100 | DT-100 Operation Manual - Page 40
    • This operation can also be performed by using the buttons on the projector. 1 Press BMENU. • The "Picture" menu screen for the selected - ADJ PRJ - ADJ Help Picture Mode Contrast Bright Color Tint Sharp CLR Temp Bright Boost Progressive Lamp Setting Reset SEL./ADJ. 0 0 0 0 0 7500K 1 Standard
  • Sharp DT 100 | DT-100 Operation Manual - Page 41
    - ADJ PRJ - ADJ Help Picture Mode Contrast Bright Color Tint Sharp CLR Temp Bright Boost Progressive Lamp Setting Reset SEL./ADJ. 0 15 0 0 0 7500K 1 Standard 3D Progressive Bright ENTER END Note • Menu buttons do not function while the projector is operating the "Auto Sync", "FREEZE", or "AV
  • Sharp DT 100 | DT-100 Operation Manual - Page 42
    Contrast 0 2 Bright 0 Color 0 Tint 0 Sharp 0 3 CLR Temp 7500K 2 Bright Boost 1 4 Progressive 3D Progressive 5 Lamp Setting Bright Reset SEL./ADJ. ENTER END Menu also press G PICTURE MODE on the remote control to select the picture mode. (See page 36.) Useful Features 41
  • Sharp DT 100 | DT-100 Operation Manual - Page 43
    images. P R For higher color temperature for cooler, bluish, fluorescent-like images. Note • Values on "CLR Temp" are only for general standard purposes. 42 5 Lamp Setting Selectable items Brightness Eco + Approx. Quiet 87% 100% Bright Fan sound Low Normal Power consumption (When using
  • Sharp DT 100 | DT-100 Operation Manual - Page 44
    on the remote control to set the resize mode. (See page 34.) 4 Selecting the Background Image Selectable items Logo Blue None Description Sharp logo Inverted image (Projected from the front of the screen with an inverted projector) Reversed image (Projected from the rear of the screen or with
  • Sharp DT 100 | DT-100 Operation Manual - Page 45
    Adjusting the Projector Function ("PRJ - ADJ" menu) Picture SCR - ADJ Auto Search Auto Sync Auto Power Off System Sound Speaker RS-232C Fan Mode PRJ - ADJ Off On On Off On 9600 bps Normal Menu operation n Page 39 Help Lamp Timer(Life) 0h 100% SEL./ADJ. ENTER END *Serviceman only 1 Auto
  • Sharp DT 100 | DT-100 Operation Manual - Page 46
    input signal is detected for more than 15 minutes, the projector will automatically enter standby mode. The Auto Power Off function will be disabled. Note • When the Auto Power Off function is set to "On", 5 minutes before the projector enters standby mode, the message "Enter STANDBY mode in X min
  • Sharp DT 100 | DT-100 Operation Manual - Page 47
    check marks (✔). • The items in the "Help" menu change, de- pending on the input signal or setting that you have selected. • If the problem is not solved, refer to "Troubleshooting". (see pages 55 and 56) Help Color is faded or poor The picture has a green or pink tint Select the signal type Adjust
  • Sharp DT 100 | DT-100 Operation Manual - Page 48
    to clean dust from the exhaust vent and the intake vent. Mild detergent diluted with water Appendix Mild detergent Wax Thinner Info • If you want to clean the air vents during projector operation, be sure to press S STANDBY/ON on the projector or eSTANDBY on the remote control and put the
  • Sharp DT 100 | DT-100 Operation Manual - Page 49
    indicator will illuminate in red. I If you try to turn on the projector a fourth time without replacing the lamp, the projector will not turn on. Indicators on the Projector Power indicator Lamp indicator Temperature warning indicator Red on Green on Red blinks Green blinks Green on Green blinks
  • Sharp DT 100 | DT-100 Operation Manual - Page 50
    , and then connect it again. • Carefully replace the lamp. (See page 51.) • Take the projector to your nearest Sharp Authorized Service Center or Dealer for repair. • Please exercise care when replacing the lamp. • Securely install the cover. • If the power indicator blinks in red even when the
  • Sharp DT 100 | DT-100 Operation Manual - Page 51
    the instructions described in this section. * If you wish, you may have the lamp replaced at your nearest Sharp Authorized Service Center or Dealer. * If the new lamp does not light after replacement, take your projector to the nearest Sharp Authorized Service Center or Dealer for repair. 50
  • Sharp DT 100 | DT-100 Operation Manual - Page 52
    Do not loosen other screws except for the lamp unit cover and lamp unit. 1 Press SSTANDBY/ON on the projector or eSTANDBY on the remote control to put the projector into standby mode. • Wait until the cooling fan stops. 2 Disconnect the power cord. • Unplug the power cord from the AC socket. • Leave
  • Sharp DT 100 | DT-100 Operation Manual - Page 53
    user service screw to secure the lamp unit cover. Info • If the lamp unit and lamp unit cover are not correctly installed, the power will not turn on, even if the power cord is connected to the projector. Securing screws 2 1 Resetting the Lamp Timer Reset the lamp timer after replacing the lamp
  • Sharp DT 100 | DT-100 Operation Manual - Page 54
    Connecting Pin Assignments COMPUTER-RGB/COMPONENT INPUT1, 2 and COMPUTER-RGB/COMPONENT OUTPUT Terminals: 15-pin Mini D-sub female connector COMPUTER-RGB Input/Output 1. Video input (red) 2. Video input (green/sync on green) 3. Video input (blue) 11 15 4. Not connected 5. Not connected 6.
  • Sharp DT 100 | DT-100 Operation Manual - Page 55
    SVGA, XGA, SXGA, SXGA+ • Intelligent Compression and Expansion System resizing technology The following is a list of modes that conform to VESA. However, this projector supports other signals that are not VESA standards. PC/MAC PC MAC 13" MAC 16" MAC 19" MAC 21" Resolution 640 × 350 640 × 400
  • Sharp DT 100 | DT-100 Operation Manual - Page 56
    Troubleshooting Problem Check Page • Projector power cord is not plugged into the wall outlet. • Power to the external connected devices is off. • The selected input mode is wrong. • Cables incorrectly connected to the projector. • Remote control battery has run out. No picture and no sound
  • Sharp DT 100 | DT-100 Operation Manual - Page 57
    is illuminating in red. up even after the Replace the lamp. projector turns on. The lamp suddenly turns off during projection. The image sometimes flickers. • Cables incorrectly connected to the projector or the connected equipment works improperly. • Select "Vertical stripes or flickering
  • Sharp DT 100 | DT-100 Operation Manual - Page 58
    Specifications Product type Projector Model DT-100 Video system NTSC3.58/NTSC4.43/PAL/ parts) Weight (approx.) 8.6 lbs. (3.9 kg) Replacement parts Remote control, Power cord for U.S. and Canada, etc., 3 RCA to 15-pin D-sub adaptor, Operation manual As a part of policy of continuous improvement, SHARP
  • Sharp DT 100 | DT-100 Operation Manual - Page 59
    Dimensions Units: inches (mm) 13 64/ (5) 11 1/32 (280) 23 64/ (9) 2 7/8 (73) 1 55 64/ (47) 7/16 (11) 4 19 64/ (109) ø9 7/64 (69.2) 3 5/32 (80) 12 /13 32 (315) 3 1/16 (77.5) 58 1 /11 32 (33.8) 2 /61 64 (75) 1 /53 64 (46.2) 2 /19 32 (65.5) 7/16 (11) 1 7/8 (47.5) 4 7/64 (104)
  • Sharp DT 100 | DT-100 Operation Manual - Page 60
    27 Auto Power Off 45 Auto Color Temperature 42 Color 42 Contrast 42 ENTER button 39 Exhaust Remote control 13 Remote control sensor 15 Replacing the lamp 50, 51 Resize 34, 43 RESIZE button 34 RETURN button 39 RGB cable 25 SCR - ADJ 43 Screen Size and Projection Distance 20 Sharp
  • Sharp DT 100 | DT-100 Operation Manual - Page 61
    Coverage (if any): Where to Obtain Service: What to do to Obtain Service: DT-100 Projector (Be sure to have this information available when you need service for your Product.) One (1) year parts and labor from date of purchase except for the Projector Lamp for which the warranty period is ninety
  • Sharp DT 100 | DT-100 Operation Manual - Page 62
    or inappropriate use as outlined in the owner's manual. (b) Any Sharp product tampered with, modified, adjusted or repaired by any party other than Sharp, Sharp's Authorized Service Centres or Sharp's Authorized Servicing Dealers. (c) Damage caused or repairs required as a result of the use with
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
ENGLISH
FRANÇAIS
ESPAÑOL
PROJECTOR
PROJECTEUR
PROYECTOR
DT-100
OPERATION MANUAL
MODE D’EMPLOI
MANUAL DE MANEJO