Sharp FO-2081 FO-2081 Operation Guide (for general information) - Page 61

If the tray runs out of paper during printing, Cancel a print job

Get Sharp FO-2081 PDF manuals and user guides View all Sharp FO-2081 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 61 highlights

PRINTER FUNCTIONS If the tray runs out of paper during printing Printing will automatically resume when paper is loaded in the tray. When using the bypass tray, select printer mode with the mode select key on the machine, load paper as instructed by the message in the display, and then press the [START] key to resume printing. When the 250-sheet paper feed unit is installed: Note that if the "AUTO TRAY SWITCH" setting in the user programs is enabled and there is the same size of paper in another tray, the machine will automatically switch to the other tray and continue printing. Cancel a print job To cancel a print job that is already in progress, select printer mode with the mode select key on the machine and then press the [CLEAR] key ( ) or the [CLEAR ALL] key ( ). "CANCEL PRINT JOB?" will appear in the display. Select "YES" and press the [OK] key. When "Paper Source" is set to "Auto Select" If "Paper Source" is set to "Auto Select" in the "Paper" tab of the printer driver setup screen and the correct size of paper for a print job is not loaded in the machine, the printing procedure will vary depending on the "FORCED OUTPUT" setting in the user programs (see "USER PROGRAMS" in the Operation Guide). When "FORCED OUTPUT" is set to "OFF" Select printer mode with the mode select key on the machine, check the message in the display, load paper in the bypass tray, and then press the [START] key to begin printing. When "FORCED OUTPUT" is set to "ON" Printing takes place on the paper loaded in the machine, even though the paper size is different from the print image size. 60

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
PRINTER FUNCTIONS
60
If the tray runs out of paper during printing
Printing will automatically resume when paper is loaded in the tray.
When using the bypass tray, select printer mode with the mode select key on the
machine, load paper as instructed by the message in the display, and then press the
[START] key to resume printing.
When the 250-sheet paper feed unit is installed:
Note that if the "AUTO TRAY SWITCH" setting in the user programs is enabled and
there is the same size of paper in another tray, the machine will automatically switch
to the other tray and continue printing.
Cancel a print job
To cancel a print job that is already in progress, select printer mode with the mode
select key on the machine and then press the [CLEAR] key (
) or the [CLEAR
ALL] key (
).
"CANCEL PRINT JOB?" will appear in the display. Select "YES" and press the [OK]
key.
When "Paper Source" is set to "Auto Select"
If "Paper Source" is set to "Auto Select" in the "Paper" tab of the printer driver setup
screen and the correct size of paper for a print job is not loaded in the machine, the
printing procedure will vary depending on the "FORCED OUTPUT" setting in the
user programs (see "USER PROGRAMS" in the Operation Guide).
When "FORCED OUTPUT" is set to "OFF"
Select printer mode with the mode select key on the machine, check the message in
the display, load paper in the bypass tray, and then press the [START] key to begin
printing.
When "FORCED OUTPUT" is set to "ON"
Printing takes place on the paper loaded in the machine, even though the paper size
is different from the print image size.