Sharp FP-N60CX FP-N60CX Operation Manual - Page 11

Clean-sign Light - hepa filter

Page 11 highlights

Pollen Mode Indicator Light MAX POLLEN h SIGN Remote Control Receiver CLEAN-SIGN LIGHT The color changes according to the air condition. Clean (Green) Slightly Impure (Orange) Very Impure (Red) CLEAN-SIGN CLEAN-SIGN CLEAN-SIGN ABOUT THE CLEAN-SIGN • The sensors display a CLEAN-SIGN depending on relative changes to the environment from the time the power plug is inserted into the wall outlet and thereafter. • When the air is extremely impure at the time the power plug is inserted, the CLEAN-SIGN LIGHT may light green since the impure condition is the environment against which the sensors base the impurity rate on. In this case, operate the unit for a while in Clean Mode first, then switch to the desired operation mode. See Page E-15 • To reset the base impurity rate on the CLEAN-SIGN remove and insert the power plug. • The CLEAN-SIGN LIGHT can be turned off using the "Display ON/ OFF" Button of the Remote Control. See Page E-15 ENGLISH MODE-ON / OFF button See Page E-14 (Used to select operations or turn the unit off) Sensor sensitivity select switch The unit's sensitivity to odor and dust detection can be adjusted. This setting is factory set to "NORMAL", and it is recommended that you use the unit in this setting. Set the sensitivity to "SENSITIVE" if the sensitivity seems too low depending on the room condition. Filter Reset Button SENSOR NORMAL SENSITIVE FILTER RESET Odor Sensor Detects odors such as tobacco smoke, pets, cosmetics, etc. Sensor Cover Dust Sensor Detects dusts, smoke, pollen, house dust, etc. See Page E-18,E-20 Main Unit *Before pressing the Filter Reset Button, be sure that the unit is plugged in. There is also a Filter Reset Button on the remote control. After cleaning and reinserting the Washable Active Carbon Filter, press the Filter Reset Button. Filter Frame True HEPA Filter (white) See Page E-19 (Dust Collection Filter with Anti-Bacterial Apatite Filter sheet covering its front surface) Washable Active Carbon Filter (black) (Deodorizing Filter)See Page E-16 Filter Separator Pre-Filter Front Panel Hook Remote Control See Page E-15 E-9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48

ENGLISH
E-9
Pollen Mode Indicator
Light
Remote Control Receiver
MODE-ON / OFF button
See Page E-14
(Used to select operations or turn the unit off)
Sensor sensitivity select switch
The unit’s sensitivity to odor and dust detection can be ad-
justed. This setting is factory set to “NORMAL”, and it is rec-
ommended that you use the unit in this setting. Set the sen-
sitivity to “SENSITIVE” if the sensitivity seems too low de-
pending on the room condition.
Filter Reset Button
Odor Sensor
Detects odors such as tobacco smoke, pets, cosmetics, etc.
Sensor Cover
Dust Sensor
Detects dusts, smoke, pollen, house dust, etc. See Page E-18,E-20
Main Unit
Filter Frame
True HEPA Filter (white)
See Page E-19
(Dust Collection Filter with Anti-Bacterial Apatite Filter sheet covering its front surface)
Washable Active Carbon Filter (black)
(Deodorizing Filter)
See Page E-16
Filter Separator
Pre-Filter
Front Panel
Hook
Remote Control
See Page E-15
CLEAN-SIGN LIGHT
The color changes according to the air condition.
Clean (Green)
Slightly Impure (Orange)
Very Impure (Red)
ABOUT THE CLEAN-SIGN
• The sensors display a CLEAN-SIGN depending on relative changes
to the environment from the time the power plug is inserted into the
wall outlet and thereafter.
• When the air is extremely impure at the time the power plug is in-
serted, the CLEAN-SIGN LIGHT may light green since the impure
condition is the environment against which the sensors base the im-
purity rate on. In this case, operate the unit for a while in Clean Mode
first, then switch to the desired operation mode. See Page E-15
• To reset the base impurity rate on the CLEAN-SIGN remove and
insert the power plug.
• The CLEAN-SIGN LIGHT can be turned off using the “Display ON/
OFF” Button of the Remote Control. See Page E-15
*Before pressing the Filter Reset But-
ton, be sure that the unit is plugged in.
There is also a Filter Reset Button on
the remote control.
After cleaning and reinserting the
Washable Active Carbon Filter, press
the Filter Reset Button.
CLEAN-SIGN
CLEAN-SIGN
CLEAN-SIGN
MAX
h
POLLEN
SIGN
SENSOR
NORMAL
SENSITIVE
FILTER RESET