Sharp MD-M3 Operation Manual - Page 24

To try to store a station name again, if the, wrong name was stored in memory by mis

Get Sharp MD-M3 PDF manuals and user guides View all Sharp MD-M3 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

(Continued) To try to store a station name again, if the wrong name was stored in memory by mistake: When you store station names in memory using the ASPM function, the correct station names may not actually be stored if there is lots of noise or if the RDS station signal is too weak. In this case, try storing station names in memory using the following procedure. 1,3 4,5 2 Notes: q When there are no station names stored in memory, you cannot use this function. In this case, when the STATION button is pressed, "NOTHING" will flash for 5 seconds, and the unit will return to the original display. q This function can only be used when the FM band has been selected. q The same station name can be stored in different preset channels. Therefore, when you are choosing a station name from the presets, the same station name may be encountered more than once. q In a certain area or during certain time periods, the station names selected using the station select function may temporarily be different from the name of the station you are actually receiving. 1,3 2 4,5 1 Press the STATION button. 2 Within 6 seconds, press the PRESET (X or W) button to check whether the station names are correct. 3 If you find a station name that is wrong, press the STATION button again within 6 seconds to recall the preset station, which corresponds to the station name. 4 After the preset station has been received and the correct station name has been displayed, press the MEMORY button. 5 Within 5 seconds, Press the MEMORY button again whilst the preset channel number is flashing. q The new station name has been stored in memory correctly. 22

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
22
To try to store a station name again, if the
wrong name was stored in memory by mis-
take:
When you store station names in memory using
the ASPM function, the correct station names may
not actually be stored if there is lots of noise or if
the RDS station signal is too weak.
In this case, try storing station names in memory
using the following procedure.
Notes:
●
When there are no station names stored in
memory, you cannot use this function. In this
case, when the STATION button is pressed,
"NOTHING" will flash for 5 seconds, and the unit
will return to the original display.
●
This function can only be used when the FM band
has been selected.
●
The same station name can be stored in differ-
ent preset channels. Therefore, when you are
choosing a station name from the presets, the
same station name may be encountered more
than once.
●
In a certain area or during certain time periods,
the station names selected using the station se-
lect function may temporarily be different from
the name of the station you are actually receiv-
ing.
(Continued)
2
1,3
4,5
2
1,3
4,5
1
Press the STATION button.
2
Within 6 seconds, press the PRESET (
X
or
W
)
button to check whether the station names are
correct.
3
If you find a station name that is wrong, press
the STATION button again within 6 seconds to
recall the preset station, which corresponds to
the station name.
4
After the preset station has been received and
the correct station name has been displayed,
press the MEMORY button.
5
Within 5 seconds, Press the MEMORY button
again whilst the preset channel number is flash-
ing.
●
The new station name has been stored in
memory correctly.