Sharp PG M20X PG-M20X Operation Manual - Page 32

Image Projection, Basic Procedure - reset

Get Sharp PG M20X - Notevision XGA DLP Projector PDF manuals and user guides
UPC - 074000358355
View all Sharp PG M20X manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

Image Projection Basic Procedure Connect the required external equipment to the projector before operating the following procedures. The language preset at the factory is English. If you want to change the on-screen display to another language, reset the language according to the procedure on page 30. 1 Plug the power cord into the wall outlet. • The POWER indicator illuminates up in red, and the projector enters standby mode. 2 Press on the projector or on the remote control. • The POWER indicator illuminates in green. After the LAMP REPLACEMENT indicator illuminates, the projector is ready to start operation. Note • The LAMP REPLACEMENT indicator illuminates, indicating the status of the lamp. Green: The lamp is ready. Green blinking: The lamp is warming up. Red: The lamp should be replaced. • If the power is turned off and on right after again, the LAMP REPLACEMENT indicator may take time to illuminate. When "Anti-Theft" is set, the keycode input box will appear. • Enter the keycode. Note • When entering the keycode, press the buttons previously set on the projector or the remote control. Info • When "Anti-Theft" is set, enter the keycode or the input display will not appear. Even when the signal is input, the display cannot appear. -28 MProjector indicators LAMP REPLACEMENT indicator POWER indicator POWER button INPUT button MENU button buttons ENTER button POWER button INPUT 1/2/3 buttons MENU button buttons ENTER button MKeycode input box

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
Image Projection
Basic Procedure
Connect the required external equipment to
the projector before operating the following
procedures.
The language preset at the factory is English.
If you want to change the on-screen display
to another language, reset the language ac-
cording to the procedure on page
30
.
1
Plug the power cord into the
wall outlet.
•
The POWER indicator illuminates up
in red, and the projector enters
standby mode.
2
Press
on the projector or
on the remote control.
•
The POWER indicator illuminates in
green. After the LAMP REPLACEMENT
indicator illuminates, the projector is
ready to start operation.
Note
•
The LAMP REPLACEMENT indica-
tor illuminates, indicating the status
of the lamp.
Green:
The lamp is ready.
Green blinking:
The lamp is
warming up.
Red:
The lamp should be replaced.
•
If the power is turned off and on right
after again, the LAMP REPLACEMENT
indicator may take time to
illuminate
.
When “Anti-Theft” is set, the
keycode input box will appear.
•
Enter the keycode.
Note
•
When entering the keycode, press
the buttons previously set on the
projector or the remote control.
Info
•
When “Anti-Theft” is set, enter the
keycode or the input display will not
appear. Even when the signal is in-
put, the display cannot appear.
▼
Projector indicators
LAMP REPLACEMENT indicator
POWER indicator
POWER button
POWER button
INPUT
button
MENU
button
buttons
ENTER
button
INPUT 1/2/3 buttons
MENU button
buttons
ENTER button
▼
Keycode input box
-28