Sharp PN-UH701 PN-UH601 PN-UH701 Operation Manual - Page 66

Control of the TV Continue

Get Sharp PN-UH701 PDF manuals and user guides View all Sharp PN-UH701 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 66 highlights

sharp operation manual >> Using a PC

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
sharp operation manual
file:///Y|/11_IM%20GROUP/Oversea%20Group/SHARP%20JAPAN/JC180020_PN-UH601_PN-UH701_HTML/HTML/eng/7-2.html[2/28/2018 7:08:57 PM]
>>
<<
Using a PC
ENG 7-2
Control of the TV (Continue)
Command format
Eight ASCII codes +CR
Command 4-digits: Command. The text of four characters.
Parameter 4-digits: Parameter 0–9, x, blank, ?
Parameter
Input the parameter values, aligning left, and fill with blank(s) for the remainder. (Be sure that 4
values are input for the parameter.)
When the input parameter is not within an adjustable range, "ERR" returns. (Refer to "Response
code format".)
Any numerical value can replace the "x" on the table.
Response code format
Normal response
Problem response
(communication error or incorrect command)
Command table
Commands not indicated here are not guaranteed to operate.
CONTROL ITEM
COMMAND
PARAMETER
CONTROL CONTENTS
POWER SETTING *2
P
O
W
R
0
_
_
_
Power
Off
It shifts to standby.
1
_
_
_
Power
On
Power On *1
INPUT
SELECTION
TOGGLE
I
T
G
D
_
_
_
_
(Toggle)
It input-switches by the toggle.
(It is the same as an input
change key)
TV
I
T
V
D
0
_
_
_
It input-switches to TV. (A
channel remains as it is. (Last
memory))
*1 Select "Initial Setup" from the menu screen and set "Quick Start Mode" to "On" to enable the
Power On command for LAN and Wi-Fi.
When "Quick Start Mode" is set to "Off" and "Wake on Wi-Fi/LAN" is set to "Enable", you can
use "Wake on LAN (Magic Packet)" to turn on the power via LAN.
When "Quick mode" is "Off" and the power of the display is off, you can use only "POWR1"
command by setting the baud rate as "9,600" on PC side.
After using "POWR1" command, the baud rate becomes the original setting before turning off
the display.
*2 The minijack (Terminal: “SERVICE ONLY”) outputs the system boot message for service other
than command response when the TV turns on / off. Please ignore the system boot message.
NOTE
If an underbar (_) appears in the parameter column, enter a space.
If an asterisk (*) appears, enter a value in the range indicated in brackets under CONTROL
CONTENTS.
Any numerical value can replace the "x" on the table.