Sharp XR-1S XR-1S , XR-1X Operation Manual - Page 65

Appendix

Get Sharp XR-1S - Notevision SVGA DLP Projector PDF manuals and user guides
UPC - 074000364103
View all Sharp XR-1S manuals
Add to My Manuals
Save this manual to your list of manuals

Page 65 highlights

Problem Check Page Picture is green on • Change the input signal type setting. INPUT 1 COMPONENT. Picture is pink (no green) on INPUT 1 RGB. Picture is too bright and • Image adjustments are incorrectly set. whitish. The cooling fan becomes • When temperature inside the projector increases, the cooling fan noisy. runs faster. The lamp does not light • The lamp indicator is illuminating in red. up even after the Replace the lamp. projector turns on. The lamp suddenly turns off during projection The image sometimes • Cables incorrectly connected to the projector or the connected flickers. equipment works improperly. • If this happens frequently, replace the lamp. The lamp needs much • The lamp will eventually need to be changed. time to turn on. While the remaining lamp life draws to a close, replace the lamp. Picture is dark. 51 40 - 53 23, 24, 25, 51, 56 56 This unit is equipped with a microprocessor. Its performance could be adversely affected by incorrect operation or interference. If this should happen, unplug the Unit and plug it in again after more than 30 seconds. Appendix 61

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
61
Appendix
Problem
Picture is green on
INPUT 1 COMPONENT.
Picture is pink (no green)
on INPUT 1 RGB.
Picture is too bright and
whitish.
The cooling fan becomes
noisy.
The lamp does not light
up even after the
projector turns on.
The lamp suddenly turns
off during projection
The image sometimes
flickers.
The lamp needs much
time to turn on.
Picture is dark.
Check
•
Change the input signal type setting.
•
Image adjustments are incorrectly set.
•
When temperature inside the projector increases, the cooling fan
runs faster.
•
The lamp indicator is illuminating in red.
Replace the lamp.
•
Cables incorrectly connected to the projector or the connected
equipment works improperly.
•
If this happens frequently, replace the lamp.
•
The lamp will eventually need to be changed.
While the remaining lamp life draws to a close, replace the lamp.
Page
51
40
–
53
23
,
24
,
25
,
51
,
56
56
This unit is equipped with a microprocessor. Its performance could be adversely affected by incorrect operation
or interference. If this should happen, unplug the Unit and plug it in again after more than 30 seconds.