Sharp XV-Z10000 Operation Manual - Page 33

Image Projection - reset

Get Sharp XV-Z10000 PDF manuals and user guides View all Sharp XV-Z10000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

Image Projection Basic Procedure Connect the required external equipment to the projector before operating the following procedures. Info • The language preset at the factory is English. If you want to change the on-screen display to another language, reset the language according to the procedure on page 34. 1 Plug the power cord into the wall outlet. • The power indicator illuminates red, and the projector enters standby mode. 2 Press on the remote control or on the projector. • The power indicator illuminates blue. After the lamp replacement indicator illuminates, the projector is ready to start operation. Lamp replacement indicator ", ',\, | buttons ENTER button Note • The lamp replacement indicator illuminates, indicating the status of the lamp. Blue: The lamp is ready. Blue blinking: The lamp is warming up. Red: The lamp should be replaced. • If the power is turned off and immediately switched on again, the lamp replacement indicator may take time to illuminate. • When controlling the projector using RS-232C commands from a computer, wait for at least 30 seconds after the power has been turned on, and then transmit the commands. Power (OFF) button ENTER button Power indicator MENU button INPUT button Power (OFF) button Power (ON) button Power (ON) button MENU button ', ", \, | buttons INPUT buttons -32 XV-Z10000#Print#p31_39.p65 32 02.10.25, 7:29 PM

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
Image Projection
Basic Procedure
Connect the required external equipment to
the projector before operating the following
procedures.
Info
•
The language preset at the factory is English.
If you want to change the on-screen display
to another language, reset the language ac-
cording to the procedure on page
34
.
1
Plug the power cord into the
wall outlet.
•
The power indicator illuminates red, and
the projector enters standby mode.
2
Press
on the remote control
or
on the projector.
•
The power indicator illuminates blue.
After the lamp replacement indicator il-
luminates, the projector is ready to start
operation.
Note
•
The lamp replacement indicator il-
luminates, indicating the status of the
lamp.
Blue:
The lamp is ready.
Blue blinking:
The lamp is
warming up.
Red:
The lamp should be replaced.
•
If the power is turned off and imme-
diately switched on again, the lamp
replacement indicator may take time
to illuminate.
•
When controlling the projector using
RS-232C commands from a com-
puter, wait for at least 30 seconds
after the power has been turned on,
and then transmit the commands.
-32
Lamp
replacement
indicator
Power indicator
INPUT
button
Power (ON)
button
Power (OFF)
button
MENU button
"
,
'
,
\
,
|
buttons
ENTER
button
Power (ON)
button
INPUT
buttons
'
,
"
,
\
,
|
buttons
MENU button
ENTER
button
Power (OFF)
button
XV-Z10000#Print#p31_39.p65
02.10.25, 7:29 PM
32