Sharp XV-Z10000 Operation Manual - Page 87

For SHARP Assistance U.S.A only

Get Sharp XV-Z10000 PDF manuals and user guides View all Sharp XV-Z10000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 87 highlights

Troubleshooting Problem Picture is green on INPUT 1 or 2 COMPONENT. Picture is pink (no green) on INPUT 1 or 2 RGB. Picture is dark. Picture is too bright and whitish. A response code cannot be received when the projector was attempted to be controlled using RS-232C commands from a computer during standby. Check • Change the input signal type setting. • The lamp replacement indicator is blinking in red. Replace the lamp. • Picture adjustments are incorrectly set. • In the case of transmitting RS-232C commands from a computer during standby, it takes a maximum of 30 seconds for the computer to receive the response code. Set the response code waiting time of the computer to 30 seconds or more. Page 64 74 44 80 For SHARP Assistance (U.S.A only) If you encounter any problems during setup or operation of this projector, first refer to the "Troubleshooting" section on this page. If this operation manual does not answer your question, please call toll free 1-877-DTV-SHARP (1-877-388-7427) for further assistance. Or, send us an e-mail at [email protected] . Our World Wide Web address is http://www.sharpusa.com/ . -86 XV-Z10000#Print#p85_92.p65 86 02.10.25, 7:35 PM

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
-86
Check
Problem
Page
Picture is green on
INPUT 1 or 2
COMPONENT.
Picture is pink (no green)
on INPUT 1 or 2 RGB.
•
Change the input signal type setting.
64
•
The lamp replacement indicator is blinking in red. Replace the
74
lamp.
•
Picture adjustments are incorrectly set.
44
•
In the case of transmitting RS-232C commands from a computer
80
during standby, it takes a maximum of 30 seconds for the
computer to receive the response code. Set the response code
waiting time of the computer to 30 seconds or more.
Troubleshooting
Picture is dark.
Picture is too bright and
whitish.
A response code cannot
be received when the
projector was attempted
to be controlled using
RS-232C commands
from a computer during
standby.
For SHARP Assistance (U.S.A only)
If you encounter any problems during setup or operation of this projector, first refer to the “Trouble-
shooting” section on this page. If this operation manual does not answer your question, please call
toll free 1-877-DTV-SHARP (1-877-388-7427) for further assistance.
Or, send us an e-mail at
Our World Wide Web address is http://www.sharpusa.com/ .
XV-Z10000#Print#p85_92.p65
02.10.25, 7:35 PM
86