Sharp XV-Z10000 Operation Manual - Page 79

Resetting the Lamp Timer

Get Sharp XV-Z10000 PDF manuals and user guides View all Sharp XV-Z10000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 79 highlights

4 Remove the lamp unit. • Loosen the securing screws from the lamp unit. Hold the lamp unit by the handle and pull it in the direction of the arrow. 5 Insert the new lamp unit. • Press the lamp unit firmly into the lamp unit compartment. Fasten the securing screws. 6 Attach the lamp unit cover. • Close the lamp unit cover in the direction of the arrow (to the close mark) on the side of the projector. Then tighten the user service screw. Info • If the lamp unit and lamp cover are not correctly installed, the power will not turn on, even if the power cord is connected to the projector. Resetting the Lamp Timer Reset the lamp timer after replacing the lamp. 1 Connect the power cord. • Plug the power cord into the AC socket of the projector. 2 Reset the lamp timer. • While holding down , " and | on the projector, press tor. on the projec- • "LAMP 0000H" is displayed, indicating that the lamp timer is reset. Info • Make sure to reset the lamp timer only when replacing the lamp. If you reset the lamp timer and continue to use the same lamp, this may cause the lamp to become damaged or explode. -78 XV-Z10000#Print#p71_84.p65 78 2 1 User service screws 02.10.25, 7:34 PM

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
User service screws
1
2
4
Remove the lamp unit.
•
Loosen the securing screws from the
lamp unit. Hold the lamp unit by the
handle and pull it in the direction of
the arrow.
5
Insert the new lamp unit.
•
Press the lamp unit firmly into the lamp
unit compartment. Fasten the secur-
ing screws.
6
Attach the lamp unit cover.
•
Close the lamp unit cover in the direc-
tion of the arrow (to the close mark)
on the side of the projector. Then
tighten the user service screw.
Info
•
If the lamp unit and lamp cover are not
correctly installed, the power will not turn
on, even if the power cord is connected
to the projector.
Resetting the Lamp Timer
Reset the lamp timer after replacing the lamp.
1
Connect the power cord.
•
Plug the power cord into the AC socket
of the projector.
2
Reset the lamp timer.
•
While holding down
,
"
and
|
on
the projector, press
on the projec-
tor.
•
“
LAMP 0000H
”
is displayed, indicat-
ing that the lamp timer is reset.
Info
•
Make sure to reset the lamp timer only
when replacing the lamp. If you reset the
lamp timer and continue to use the same
lamp, this may cause the lamp to become
damaged or explode.
-78
XV-Z10000#Print#p71_84.p65
02.10.25, 7:34 PM
78