Singer XL-420 FUTURA Instruction Manual - Page 118

Helpful Tips

Get Singer XL-420 FUTURA PDF manuals and user guides View all Singer XL-420 FUTURA manuals
Add to My Manuals
Save this manual to your list of manuals

Page 118 highlights

Helpful Tips: ‡ When embroidering larger or heavier pieces of fabric, it is helpful to support the fabric on a table in front and EDFNRIWKHPDFKLQH ‡ :KHQZRUNLQJZLWKVSHFLDOW\WKUHDGV VXFKDVPHWDOOLF threads) or designs with dense stitch areas, it is recommended that you lower the embroidery speed. ‡ Be sure to deactivate the Thread Cutter Mode when doing endless embroidery. This will help eliminate the possibility of the thread coming out of the needle when sewing the alignment stitches and long jump stitches. ‡ To change a bobbin during embroidery, raise the needle by turning the handwheel toward you. Raise the presser foot lifter. Remove the hoop from the machine with the fabric remaining in the hoop. Remove the bobbin cover plate and empty bobbin. Wind the bobbin, insert it into the bobbin case and replace the bobbin FRYHU SODWH 3ODFH WKH KRRS EDFN RQWR WKH PDFKLQH Lower the presser foot lifter. Press the Start/Stop button to resume embroidery. ‡ Should you find that the hoop will not release from WKH PDFKLQH EHFDXVH WKH EDFN RI WKH IRRW LV FRPLQJ in contact with the endless hoop clamp, use Reverse/ Forward Stitch button to move to another area that will allow you to remove the hoop. When the bobbin has been changed, use Forward/Reverse Stitch button to PRYHWKHQHHGOHEDFNWRSRVLWLRQDQGUHVXPHVHZLQJ If this is not possible, due to the type of design you are embroidering, remove the presser foot and needle to remove the hoop from the machine. Replace the presser foot and needle to resume embroidering. 116

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
116
³
When embroidering larger or heavier pieces of fabric,
it is helpful to support the fabric on a table in front and
EDFN RI WKH PDFKLQHµ
³
:KHQ ZRUNLQJ ZLWK VSHFLDOW\ WKUHDGV ¼VXFK DV PHWDOOLF
threads) or designs with dense stitch areas, it is
recommended that you lower the embroidery speed.
³
Be sure to deactivate the
Thread Cutter Mode
when
doing endless embroidery. This will help eliminate the
possibility of the thread coming out of the needle when
sewing the alignment stitches and long jump stitches.
³
To change a bobbin during embroidery, raise the
needle by turning the handwheel toward you. Raise the
presser foot lifter. Remove the hoop from the machine
with the fabric remaining in the hoop. Remove the
bobbin cover plate and empty bobbin. Wind the bobbin,
insert it into the bobbin case and replace the bobbin
FRYHU SODWHµ 3ODFH WKH KRRS EDFN RQWR WKH PDFKLQHµ
Lower the presser foot lifter. Press the
Start/Stop
button to resume embroidery.
³
Should you find that the hoop will not release from
WKH PDFKLQH EHFDXVH WKH EDFN RI WKH IRRW LV FRPLQJ
in contact with the endless hoop clamp, use Reverse/
Forward Stitch button to move to another area that will
allow you to remove the hoop. When the bobbin has
been changed, use Forward/Reverse Stitch button to
PRYH WKH QHHGOH EDFN WR SRVLWLRQ DQG UHVXPH VHZLQJµ
If this is not possible, due to the type of design you
are embroidering, remove the presser foot and needle
to remove the hoop from the machine. Replace the
presser foot and needle to resume embroidering.
Helpful Tips: