Sony HSCU300RF Operation Manual - Page 9
Pr/R/R-Y, Y/G/Y, Pb/B/B-Y component signals, MIC/WF REMOTE/TRUNK microphone/waveform
View all Sony HSCU300RF manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 9 highlights
d Pr/R/R-Y, Y/G/Y, Pb/B/B-Y (component signals) connectors (BNC type) Outputs the HD component signals, SD component signals, HD RGB signals, or SD RGB signals from the corresponding connectors. e PIX (picture monitor output) connector (BNC type) Outputs a video signal for a picture monitor. It can also output a signal with superimposed character display. f SYNC/WF (sync signal output/waveform monitor output) connector (BNC type) Outputs a sync signal or video signal for a waveform monitor. g REMOTE connector (8-pin) Transmits and receives control signals from a MSU-1000/1500 Master Setup Unit, CNU-700 Camera Command Network Unit, or RCP-1000-series Remote Control Panel via a CCA-5 cable (optional). It also supplies power when connected to an RCP-1000-series Remote Control Panel. h INTERCOM/TALLY/PGM (intercom/tally/program audio) connector (D-sub 25-pin) Transmits and receives the various intercom, tally, and program audio signals. It connects to the intercom/tally/program audio connector of the intercom system. i MIC OUT1, MIC OUT2 (microphone output 1, 2) connectors (XLR 3-pin) Outputs the camera microphone signals. j CAMERA connector (optical fiber connector/triax connector) Connects to the camera via an optical fiber cable or a triax cable. The camera sends all video and audio signals to the CCU, and the CCU sends control signals, return video and audio signals, as well as power, to the camera over a single optical fiber cable or triax cable. k AC supply input connector Connects to the AC supply via the specified power cord (optional). A plug holder (optional) can be used to secure the power cord to the CCU. l SDI RETURN 1, 2 (SDI return video 1, 2 input) connectors (BNC type) Inputs the HD SDI return video signals or SD SDI return video signals (2-system). Can also be configured as the HD/SD SDI Prompter input connector. Note The HSCU300RF does not support SDI Prompter. m SDI OUTPUT 1 to 4 connectors (BNC type) Outputs the camera signals in HD SDI or SD SDI signal format. The SDI OUTPUT 3 and SDI OUTPUT 4 connectors can also output signals with superimposed character or marker display. n VBS 1, 2 (composite video signal 1, 2) connectors (BNC type) Outputs (2-system) the camera signals in composite signal format. o (LAN) jack (RJ-45, 8-pin) Connects to a LAN hub (10BASE-T/100BASE-TX), when using a network connection, via a LAN cable (shielded type, category 5 or higher). p MIC/WF REMOTE/TRUNK (microphone/waveform monitor remote/trunk) connector (D-sub 25-pin) Supports the following functions. • Microphone remote Connects to an external control device, such as an audio mixer, which can select the camera microphone gain to one of five values (20/30/40/50/60 dB) in response to the audio conditions when shooting. This connector can also output a red tally signal and green tally signal. • Waveform monitor remote Connects to corresponding connector on a recall-type waveform monitor. Outputs a signal used for remote control of the waveform monitor display by an MSU-1000/1500 Master Setup Unit or RCP-1000 series Remote Control Panel. For connection details, refer to the waveform monitor manual. • Waveform monitor mode output Connects to a waveform monitor and is used when monitoring each of the 3 R/G/B waveforms simultaneously in sequential mode. When the SEQ button on the MSU-1000/1500 Master Setup Unit or RCP-1000-series Remote Control Panel is pressed, the video signal output from the WF connector changes to a sequence signal. • Trunk Connects to an external device to provide a communication path between it and the external device connected to the REMOTE connector on the camera. 9 Locations and Functions of Parts