Sony HT-CT260H Operating Instructions - Page 17

Removing the stands, Installing the Sound Bar on, a wall, Getting Started, Prepare screws not supplied - no sound

Get Sony HT-CT260H PDF manuals and user guides View all Sony HT-CT260H manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

Getting Started Removing the stands When the Sound Bar is to be placed tilting upward or on a wall, remove the 2 stands at the bottom of the Sound Bar, as shown below. 1 Prepare screws (not supplied) that are suitable for the holes on the back of the Sound Bar. 4 mm (3/16 inches) More than 30 mm (1 1/4 inches) Stand 5 mm (7/32 inches) 10 mm (13/32 inches) Hole on the back of the Sound Bar Installing the Sound Bar on a wall You can install the Sound Bar on the wall. Notes  Use screws that are suitable for the wall material and strength. As a plaster board wall is especially fragile, attach the screws securely to a wall beam. Install the Sound Bar on a vertical and flat reinforced area of the wall.  Be sure to subcontract the installation to Sony dealers or licensed contractors and pay special attention to safety during the installation.  Sony is not responsible for accidents or damage caused by improper installation, insufficient wall strength, improper screw installation or natural calamity, etc. 2 Fasten the screws to the wall. The screws should protrude 11 to 12 mm (approx. 15/32 inches). 592 mm (23 5/16 inches) 11 to 12 mm (approx. 15/32 inches) continued 17US

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
17
US
Getting Started
When the Sound Bar is to be placed
tilting upward or on a wall, remove the
2 stands at the bottom of the Sound
Bar, as shown below.
You can install the Sound Bar on the
wall.
Use screws that are suitable for the wall
material and strength. As a plaster
board wall is especially fragile, attach
the screws securely to a wall beam.
Install the Sound Bar on a vertical and
flat reinforced area of the wall.
Be sure to subcontract the installation
to Sony dealers or licensed contractors
and pay special attention to safety
during the installation.
Sony is not responsible for accidents or
damage caused by improper
installation, insufficient wall strength,
improper screw installation or natural
calamity, etc.
1
Prepare screws (not supplied)
that are suitable for the holes on
the back of the Sound Bar.
2
Fasten the screws to the wall.
The screws should protrude 11 to
12 mm (approx. 15/32 inches).
Removing the stands
Installing the Sound Bar on
a wall
Notes
Stand
Hole on the back of the Sound Bar
4 mm
(3/16 inches)
More than 30 mm (1 1/4 inches)
5 mm
(7/32 inches)
10 mm
(13/32 inches)
592 mm
(23 5/16 inches)
11 to 12 mm
(approx.
15/32 inches)
continued