Sony HT-DDW795 Operating Instructions - Page 21

: Calibrating the appropriate settings automatically (AUTO CALIBRATION), AUTO CALIBRATION - remote

Get Sony HT-DDW795 - 5.1ch Component Home Theater System PDF manuals and user guides View all Sony HT-DDW795 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

Getting Started Inserting batteries into the remote Insert two R6 (size-AA) batteries in the RM-AAU013 remote commander. Observe the correct polarity when installing batteries. Notes • Do not leave the remote in an extremely hot or humid place. • Do not use a new battery with old ones. • Do not mix alkaline batteries and other kinds of batteries. • Do not expose the remote sensor to direct sunlight or lighting apparatuses. Doing so may cause a malfunction. • If you do not intend to use the remote for an extended period of time, remove the batteries to avoid possible damage from battery leakage and corrosion. • When you replace the batteries, the remote buttons may be reset to their factory settings. If this happens, reassign the buttons again (page 50). Tip Under normal conditions, the batteries should last for about 3 months. When the remote no longer operates the receiver, replace all the batteries with new ones. 6: Calibrating the appropriate settings automatically (AUTO CALIBRATION) The DCAC (Digital Cinema Auto Calibration) function allows you to perform automatic calibration such as: • Checking the connection between each speaker and the receiver. • Adjusting the speaker level. • Measuring the distance of each speaker from your listening position. You can also adjust the speaker levels and balance manually. For details, see "7: Adjusting the speaker levels and balance (TEST TONE)" (page 25). Before you perform Auto Calibration Before you perform Auto Calibration, install and connect the speakers (page 11, 13). • During calibration, the sound that comes out of the speakers is very loud. Pay attention to the presence of children or to the effect on your neighborhood. • Perform Auto Calibration in a quiet environment to avoid the effect of noise and to get a more accurate measurement. • If there are any obstacles in the path between the optimizer microphone and the speakers, the calibration cannot be performed correctly. Remove any obstacles from the measurement area to avoid measurement error. Note The Auto Calibration function does not work when headphones are connected. continued 21US

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
21
US
Getting Started
Insert two R6 (size-AA) batteries in the
RM-AAU013 remote commander.
Observe the correct polarity when installing
batteries.
Notes
• Do not leave the remote in an extremely hot or
humid place.
• Do not use a new battery with old ones.
• Do not mix alkaline batteries and other kinds of
batteries.
• Do not expose the remote sensor to direct sunlight
or lighting apparatuses. Doing so may cause a
malfunction.
• If you do not intend to use the remote for an
extended period of time, remove the batteries to
avoid possible damage from battery leakage and
corrosion.
• When you replace the batteries, the remote buttons
may be reset to their factory settings. If this
happens, reassign the buttons again (page 50).
Tip
Under normal conditions, the batteries should last
for about 3 months. When the remote no longer
operates the receiver, replace all the batteries with
new ones.
6: Calibrating the
appropriate settings
automatically
(AUTO CALIBRATION)
The DCAC (Digital Cinema Auto Calibration)
function allows you to perform automatic
calibration such as:
•
Checking the connection between each
speaker and the receiver.
•
Adjusting the speaker level.
•
Measuring the distance of each speaker from
your listening position.
You can also adjust the speaker levels and
balance manually. For details, see
“7: Adjusting the speaker levels and balance
(TEST TONE)” (page 25).
Before you perform Auto Calibration, install
and connect the speakers (page 11, 13).
•
During calibration, the sound that comes out
of the speakers is very loud. Pay attention to
the presence of children or to the effect on
your neighborhood.
•
Perform Auto Calibration in a quiet
environment to avoid the effect of noise and
to get a more accurate measurement.
•
If there are any obstacles in the path between
the optimizer microphone and the speakers,
the calibration cannot be performed
correctly. Remove any obstacles from the
measurement area to avoid measurement
error.
Note
The Auto Calibration function does not work when
headphones are connected.
Inserting batteries into the
remote
Before you perform Auto
Calibration
continued