Sony HT-DDW795 Operating Instructions - Page 23

When error codes appear, To rectify the error, Error codes and remedies, Error and warning codes - error 12

Get Sony HT-DDW795 - 5.1ch Component Home Theater System PDF manuals and user guides View all Sony HT-DDW795 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

Getting Started 2 Measurement starts. The measurement process will take a few minutes to complete. The table below shows the display when measurement starts. Measurement for Display Environment noise NOISE.CHK level Speaker connection MEASURE and SP DET. appears alternately* Speaker level MEASURE and GAIN appears alternately* Speaker distance MEASURE and DISTANCE appears alternately* * The corresponding speaker indicator lights up in the display during measurement. 3 Measurement ends. "COMPLETE" appears on the display and the settings are registered. 4 Disconnect the optimizer microphone from the receiver after you have finished. Note Auto Calibration cannot detect the sub woofer. Therefore, all sub woofer settings will be maintained. Tip During the measurement process, Auto Calibration is canceled when you do the following. - Press ?/1, input buttons or MUTING. - Change the volume level. - Press AUTO CAL again. Error and warning codes When error codes appear When an error is detected during Auto Calibration, an error code will appear on the display cyclically after each measurement process as follows: Error code t blank display t (error code t blank display)a) t PUSH t blank display t ENTER a)Appears when there are more than one error code. To rectify the error 1 Record down the error code. 2 Press . 3 Press ?/1 to turn off the receiver. 4 Rectify the error. For details, see "Error codes and remedies" below. 5 Turn on the receiver and perform Auto Calibration again (page 22). Error codes and remedies Error code ERROR 10 ERROR 11 ERROR 12 ERROR 20 ERROR 21 Cause and remedy The environment is too noisy. Make sure the environment is quiet during Auto Calibration. The speakers are placed too near the optimizer microphone. Place your speakers further away from the optimizer microphone. None of the speakers are detected. Make sure that the optimizer microphone is connected properly and perform Auto Calibration again. Front speakers are not detected or only one front speaker is detected. Check the front speaker connection. Only one surround speaker is detected. Check the surround speaker connection. continued 23US

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
23
US
Getting Started
2
Measurement starts.
The measurement process will take a few
minutes to complete.
The table below shows the display when
measurement starts.
* The corresponding speaker indicator lights
up in the display during measurement.
3
Measurement ends.
“COMPLETE” appears on the display
and the settings are registered.
4
Disconnect the optimizer
microphone from the receiver
after you have finished.
Note
Auto Calibration cannot detect the sub woofer.
Therefore, all sub woofer settings will be
maintained.
Tip
During the measurement process, Auto Calibration
is canceled when you do the following.
– Press
?
/
1
, input buttons or MUTING.
–
Change the volume level.
–
Press AUTO CAL again.
When error codes appear
When an error is detected during Auto
Calibration, an error code will appear on the
display cyclically after each measurement
process as follows:
Error code
t
blank display
t
(error code
t
blank display)
a)
t
PUSH
t
blank display
t
ENTER
a)
Appears when there are more than one error code.
To rectify the error
1
Record down the error code.
2
Press
3
Press
?
/
1
to turn off the receiver.
4
Rectify the error.
For details, see “Error codes and remedies”
below.
5
Turn on the receiver and perform Auto
Calibration again (page 22).
Error codes and remedies
Measurement for
Display
Environment noise
level
NOISE.CHK
Speaker connection
MEASURE and SP
DET. appears
alternately*
Speaker level
MEASURE and GAIN
appears alternately*
Speaker distance
MEASURE and
DISTANCE appears
alternately*
Error and warning codes
Error code
Cause and remedy
ERROR 10
The environment is too noisy.
Make sure the environment is quiet
during Auto Calibration.
ERROR 11
The speakers are placed too near
the optimizer microphone. Place
your speakers further away from
the optimizer microphone.
ERROR 12
None of the speakers are detected.
Make sure that the optimizer
microphone is connected properly
and perform Auto Calibration
again.
ERROR 20
Front speakers are not detected or
only one front speaker is detected.
Check the front speaker
connection.
ERROR 21
Only one surround speaker is
detected. Check the surround
speaker connection.
continued