Sony SDM-N50PS Operating Instructions (primary manual) - Page 5

To install the display horizontally or vertically, To close the display stand, To adjust the angle, - used

Get Sony SDM-N50PS PDF manuals and user guides View all Sony SDM-N50PS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 5 highlights

To install the display horizontally or vertically This display can be installed either horizontally or vertically using the supplied display stand. Open the display stand until the click sound is heard. Put the display on the stand, aligning the mark which shows the stand position on the display. To switch to the horizontal or vertical viewing position, see page 10. Horizontal installation To adjust the angle This display can be adjusted within the angles shown below with the supplied display stand. To adjust the angle, hold the front base and push (or pull) the rear leg outward (or inward) until the desired angle is attained. To install the display on the display stand, put it softly. 40° 20° The stand positioning mark Vertical installation Note Do not exceed the angles shown above, otherwise the display could fall and cause damage or a malfunction. To use the display comfortably This display is designed so that you can set it up at a comfortable viewing angle. Adjust the viewing angle of your display according to the height of the desk and chair, and so that light is not reflected from the screen to your eyes. GB The stand positioning mark To close the display stand While sliding the stopper up, close the display stand. The stopper 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
5
GB
To install the display horizontally or vertically
This display can be installed either horizontally or vertically using
the supplied display stand.
Open the display stand until the click sound is heard.
Put the display on the stand, aligning the mark which shows the
stand position on the display.
To switch to the horizontal or vertical viewing position, see
page 10.
To close the display stand
While sliding the stopper up, close the display stand.
To adjust the angle
This display can be adjusted within the angles shown below with
the supplied display stand.
To adjust the angle, hold the front base and push (or pull) the rear
leg outward (or inward) until the desired angle is attained.
To install the display on the display stand, put it softly.
Note
Do not exceed the angles shown above, otherwise the display could fall
and cause damage or a malfunction.
To use the display comfortably
This display is designed so that you can set it up at a comfortable
viewing angle. Adjust the viewing angle of your display
according to the height of the desk and chair, and so that light is
not reflected from the screen to your eyes.
Vertical installation
Horizontal installation
The stand positioning mark
The stand positioning mark
The stopper
20°
40°