Sony VPL-FX40L Operating Instructions - Page 21

Turning Off the Power

Get Sony VPL-FX40L - XGA LCD Projector PDF manuals and user guides
UPC - 027242710436
View all Sony VPL-FX40L manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

Projecting the Picture To adjust the tilt of the installation surface If the projector is installed on an uneven surface, use the adjusters to keep the projector level. Turn to adjust Adjusters Notes • Be careful not to let the projector down on your fingers. • Do not push hard on the top of the projector with the adjuster extended. It may cause a malfunction. Turning Off the Power 1 Press the ?/1 key. "POWER OFF? Please press ?/1 key again." appears to confirm that you want to turn off the power. Note The message disappears if you press any key other than the ?/1 key, or if you do not press any key for five seconds. 2 Press the ?/1 key again. The ON/STANDBY indicator flashes in green and the fan continues to run to reduce the internal heat. Also, the ON/ STANDBY indicator flashes quickly. During this time, you will not be able to light up the ON/STANDBY indicator again with the ?/1 key. 3 Unplug the AC power cord from the wall outlet after the fan stops running and the ON/STANDBY indicator lights in red. When you cannot confirm the onscreen message When you cannot confirm the on-screen message under certain conditions, you can turn off the power by holding the ?/1 key for about one second instead of the steps 1 and 2 above. Note The internal circuitry of the Off & Go and Direct Power On/Off functions may cause the fan to continue to operate for a short time even after the ?/1 key is pressed to turn off the power and the ON/STANDBY indicator changes to red. Turning Off the Power 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
21
Turning Off the Power
Projecting the Picture
To adjust the tilt of the installation
surface
If the projector is installed on an uneven
surface, use the adjusters to keep the
projector level.
•
Be careful not to let the projector down on
your fingers.
•
Do not push hard on the top of the projector
with the adjuster extended.
It may cause a malfunction.
Turning Off the
Power
1
Press the
?
/
1
key.
“POWER OFF? Please press
?
/
1
key
again.” appears to confirm that you want
to turn off the power.
The message disappears if you press any
key other than the
?
/
1
key, or if you do not
press any key for five seconds.
2
Press the
?
/
1
key again.
The ON/STANDBY indicator flashes in
green and the fan continues to run to
reduce the internal heat. Also, the ON/
STANDBY indicator flashes quickly.
During this time, you will not be able to
light up the ON/STANDBY indicator
again with the
?
/
1
key.
3
Unplug the AC power cord from the
wall outlet after the fan stops running
and the ON/STANDBY indicator
lights in red.
When you cannot confirm the on-
screen message
When you cannot confirm the on-screen
message under certain conditions, you can
turn off the power by holding the
?
/
1
key for
about one second instead of the steps
1
and
2
above.
The internal circuitry of the Off & Go and
Direct Power On/Off functions may cause the
fan to continue to operate for a short time even
after the
?
/
1
key is pressed to turn off the
power and the ON/STANDBY indicator
changes to red.
Notes
Turn to
adjust
Adjusters
Note
Note