Stihl FS 90 R Product Instruction Manual - Page 34

Balancing the, Trimmer/Brushcutter - shaft

Get Stihl FS 90 R PDF manuals and user guides View all Stihl FS 90 R manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

English Full harness Balancing the Trimmer/Brushcutter Connect machine to harness N Put on the full harness (1). N Adjust the length of the strap so that the spring hook (2) is about a hand's width below your right hip. N Balance the trimmer/brushcutter. The type and version of the harness and snap hook depend on the market. N Hook the snap hook (1) into the carrying ring (2) on the shaft N Undo the screw (3) Balance the machine The machine will balance differently depending on the cutting attachment mounted. Until the conditions listed under "Hanging positions" are met, carry out the following steps: N Move carrying ring N Tighten screw lightly N Let the machine swing until it stops moving N Check hanging position 32 FS 90, FS 90 R

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
FS 90, FS 90 R
English
32
Full harness
N
Put on the full harness (1).
N
Adjust the length of the strap so that
the spring hook
(2) is about a hand’s
width below your right hip.
N
Balance the trimmer/brushcutter.
Connect machine to harness
The type and version of the harness and
snap hook depend on the market.
N
Hook the snap hook (1) into the
carrying ring (2) on the shaft
N
Undo the screw (3)
Balance the machine
The machine will balance differently
depending on the cutting attachment
mounted.
Until the conditions listed under
"Hanging positions" are met, carry out
the following steps:
N
Move carrying ring
N
Tighten screw lightly
N
Let the machine swing until it stops
moving
N
Check hanging position
Balancing the
Trimmer/Brushcutter