Sub-Zero 427 Wine Storage Installation Instructions - Page 12

Kickplate Installation, Door Panel, Models 424G and 424FSG Installation

Get Sub-Zero 427 PDF manuals and user guides View all Sub-Zero 427 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

Models 424G and 424FSG Installation 12 Kickplate Installation Once the unit is leveled and wiring connections made, the kickplate can be installed. Use the two #10 x 1/2" stainless steel screws that are provided with the kickplate. Refer to the illustration below. IMPORTANT NOTE: The kickplate must be removed for servicing. The floor cannot interfere with removal. The louvered section of the kickplate must not be covered so as to prevent air circulation. Turn power back on to the electrical outlet. KICKPLATE Kickplate installation. Door Panel MODEL 424G Model 424G is offered in two design applications; stainless steel (/S) and overlay (/O). Each of these designs have a full-view glass door. The stainless steel model 424G/S is shipped from the factory with the decorative stainless steel door panel and matching handle in place. The overlay model 424G/O is designed to accept a decorative door panel to match surrounding cabinetry. The door panel and the handle will be provided by the customer. Before beginning installation, check for the correct components for the fit and finish desired. All overlay doors require a decorative panel 233/4" (603) x 301/16" (764), a minimum 5/8" (16) thick. IMPORTANT NOTE: For installations at or above 5,000' (1524 m) in altitude, a special high altitude glass door unit (HAG) must be ordered. If you have questions, contact your authorized Sub-Zero dealer or cabinet supplier. Additional panel information can be found in the Sub-Zero design guide. A solid panel cannot be installed over the glass door, as this may cause moisture to form behind the panel.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
Kickplate Installation
Once the unit is leveled and wiring connections made,
the kickplate can be installed. Use the two #10 x
1
/
2
"
stainless steel screws that are provided with the kickplate.
Refer to the illustration below.
IMPORTANT NOTE:
The kickplate must be removed for
servicing. The floor cannot interfere with removal. The
louvered section of the kickplate must not be covered so
as to prevent air circulation.
Turn power back on to the electrical outlet.
Door Panel
MODEL 424G
Model 424G is offered in two design applications; stain-
less steel (/S) and overlay (/O). Each of these designs have
a full-view glass door.
The stainless steel model 424G/S is shipped from the
factory with the decorative stainless steel door panel and
matching handle in place.
The overlay model 424G/O is designed to accept a deco-
rative door panel to match surrounding cabinetry. The
door panel and the handle will be provided by the
customer.
Before beginning installation, check for the correct com-
ponents for the fit and finish desired. All overlay doors
require a decorative panel 23
3
/
4
"
(603)
x 30
1
/
16
"
(764)
,a
minimum
5
/
8
"
(16)
thick.
IMPORTANT NOTE:
For installations at or above 5,000'
(1524 m)
in altitude, a special high altitude glass door unit
(HAG) must be ordered.
If you have questions, contact your authorized Sub-Zero
dealer or cabinet supplier. Additional panel information
can be found in the Sub-Zero design guide.
Models 424G and 424FSG Installation
12
KICKPLATE
Kickplate installation.
A solid panel cannot be installed over the glass door,
as this may cause moisture to form behind the panel.