Sub-Zero IC-30FI Integrated Installation Guide - Page 7

Anti-Tip Bracket

Get Sub-Zero IC-30FI PDF manuals and user guides View all Sub-Zero IC-30FI manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

SITE PREPARATION Anti-Tip Bracket WOOD FLOOR APPLICATION After properly locating the anti-tip bracket in the opening, drill pilot holes 3/16" (5) diameter maximum in the wall studs or wall plate. Use the #12 screws and washers to secure the brackets. Verify the screws penetrate through the flooring material and into wall studs or wall plate a minimum of 3/4" (19). Refer to the illustration and chart below. CONCRETE FLOOR APPLICATION After properly locating the anti-tip bracket in the opening, drill pilot holes 3/16" (5) diameter maximum in the wall studs or wall plate. Drill 3/8" (10) diameter holes into the concrete a minimum of 11/2" (38) deep. Use the #12 screws and washers to secure the brackets to the wall, and use the 3/8" wedge anchors to secure the brackets to the floor. Verify the screws penetrate wall studs or wall plate a minimum of 3/4" (19). Refer to the illustration and chart below. ANTI-TIP BRACKET PLACEMENT WIDTH 18" Models 24" Models 27" Models 30" Models 36" Models A 9" (229) 12" (305) 131/2" (343) 15" (318) 18" (457) CONCRETE WEDGE ANCHOR INSTALLATION: 1 Drill a 3/8" (10) diameter hole any depth exceeding the minimum embedment. Clean the hole or drill additional depth to accommodate drill fines. 2 Assemble the washer and nut flush with the end of anchor to protect threads. Drive the anchor through the material to be fastened until the washer is flush with the surface material. 3 Expand the anchor by tightening the nut 3-5 turns past hand-tight position or to 25 foot-pounds of torque. WARNING Verify there are no electrical wires or plumbing in the area which the screws could penetrate. CAUTION Always wear safety glasses and use other necessary protective devices or apparel when installing or working with anchors. Anchors are not recommended for use in lightweight masonry material such as block or brick, or for use in new concrete which has not had sufficient time to cure. The use of core drills is not recommended to drill holes for the anchors. A A FINISHED FLOORING WALL PLATE SUBFLOORING WOOD FLOOR Wood floor. A A FINISHED FLOORING WALL PLATE SUBFLOORING CONCRETE FLOOR 11/2"(38) min Concrete floor. subzero.com | 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
subzero.com
|
7
SITE PREPARATION
CONCRETE WEDGE ANCHOR INSTALLATION:
1
Drill a
3
/
8
"
(10)
diameter hole any depth exceeding the
minimum embedment. Clean the hole or drill additional
depth to accommodate drill fines.
2
Assemble the washer and nut flush with the end of
anchor to protect threads. Drive the anchor through the
material to be fastened until the washer is flush with the
surface material.
3
Expand the anchor by tightening the nut 3–5 turns past
hand-tight position or to 25 foot-pounds of torque.
WARNING
Verify there are no electrical wires or plumbing in the
area which the screws could penetrate.
CAUTION
Always wear safety glasses and use other neces-
sary protective devices or apparel when installing or
working with anchors.
Anchors are not recommended for use in lightweight
masonry material such as block or brick, or for use in
new concrete which has not had sufficient time to cure.
The use of core drills is not recommended to drill holes
for the anchors.
Anti-Tip Bracket
WOOD FLOOR APPLICATION
After properly locating the anti-tip bracket in the opening,
drill pilot holes
3
/
16
"
(5)
diameter maximum in the wall studs
or wall plate. Use the #12 screws and washers to secure the
brackets. Verify the screws penetrate through the flooring
material and into wall studs or wall plate a minimum of
3
/
4
"
(19)
. Refer to the illustration and chart below.
CONCRETE FLOOR APPLICATION
After properly locating the anti-tip bracket in the opening,
drill pilot holes
3
/
16
"
(5)
diameter maximum in the wall studs
or wall plate. Drill
3
/
8
"
(10)
diameter holes into the concrete
a minimum of 1
1
/
2
"
(38)
deep. Use the #12 screws and
washers to secure the brackets to the wall, and use the
3
/
8
"
wedge anchors to secure the brackets to the floor. Verify the
screws penetrate wall studs or wall plate a minimum of
3
/
4
"
(19)
. Refer to the illustration and chart below.
ANTI-TIP BRACKET PLACEMENT
WIDTH
A
18" Models
9"
(229)
24" Models
12"
(305)
27" Models
13
1
/
2
"
(343)
30" Models
15"
(318)
36" Models
18"
(457)
A
A
SUBFLOORING
WOOD FLOOR
WALL PLATE
FINISHED
FLOORING
A
A
SUBFLOORING
CONCRETE
FLOOR
WALL PLATE
FINISHED
FLOORING
1
1
/
2
"
(38)
min
Wood floor.
Concrete floor.