TP-Link TL-WR841HP TL-WR841HP V1 User Guide - Page 29

Network

Get TP-Link TL-WR841HP PDF manuals and user guides View all TP-Link TL-WR841HP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

TL-WR841HP 300Mbps High Power Router User Guide  Note: 1) The WPS LED on the Router will light green for five minutes if the device has been successfully added to the network. 2) The WPS function cannot be configured if the Wireless Function of the Router is disabled. Please make sure the Wireless Function is enabled before configuring the WPS. 4.5 Network Figure 4-5 the Network menu There are three submenus under the Network menu (shown in Figure 4-5): LAN, WAN and MAC Clone. Click any of them, and you will be able to configure the corresponding function. 4.5.1 WAN Choose menu "Network → WAN", you can configure the IP parameters of the WAN on the screen below. 1. If your ISP provides the DHCP service, please choose Dynamic IP type, and the Router will automatically get IP parameters from your ISP. You can see the page as follows (Figure 4-6): - 20 -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
TL-WR841HP
300Mbps High Power Router User Guide
- 20 -
Note:
1)
The WPS LED on the Router will light green for five minutes if the device has been
successfully added to the network.
2)
The WPS function cannot be configured if the Wireless Function of the Router is disabled.
Please make sure the Wireless Function is enabled before configuring the WPS.
4.5 Network
Figure 4-5
the Network menu
There are three submenus under the Network menu (shown in Figure 4-5):
LAN
,
WAN
and
MAC
Clone.
Click any of them, and you will be able to configure the corresponding function.
4.5.1 WAN
Choose menu “
Network
→
WAN
”, you can configure the IP parameters of the WAN on the
screen below.
1.
If your ISP provides the DHCP service, please choose
Dynamic IP
type,
and the Router will
automatically get IP parameters from your ISP. You can see the page as follows (Figure
4-6):