TRENDnet TFM-560R Manual - Page 21

Extended AT& Ampersand Command Set, Command, Options, Function & Description

Get TRENDnet TFM-560R PDF manuals and user guides View all TRENDnet TFM-560R manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

Xn Zn * W0 CONNECT result code reports DTE spee Disable protocol result codes. (see also the "Result Code Options Table") W1 CONNECT result code reports DTE spee Enable protocol result codes. W2 * CONNECT result code reports DCE spee Enable protocol result codes. Select result codes/call progress options X0 Display CONNECT or "1" for all speeds. Ignore dial tone and busy tone detection. X1 Display connect message and the modem data rate, and an indication of the modem error correction and data compression. Ignore dial tone and busy tone detection. X2 Display connect message and the modem data rate, and an indication of the modem error correction and data compression. Check dial tone before proceeding dialing, ignore busy tone detection. X3 Display connect message and the modem data rate, and an indication of the modem error correction and data compression. Ignore dial tone before proceeding dialing, check busy tone after making dialing. X4 * Display connect message and the modem data rate, and an indication of the modem error correction and data compression. Check dial tone and busy tone. X5 Same as X4. X6 Same as X4. X7 Display CONNECT or "1" for all speeds. Check dial tone and busy tone. Recall stored profile Z0 Reset and recall user profile 0. Either Z0 or Z1 restores the same single profile. Manufacturer default Extended "AT&" (Ampersand) Command Set Command &Cn Options &C0 &C1 * &Dn &D0 Function & Description Data carrier detect option State of carrier from remote modem is ignored. DCD circuit is always on DCD turns on when the remote modem's carrier signal is detected, and off when the carrier signal is not detected. Data Terminal Ready (DTR) option. DTR ignored 1-21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
1-21
W0
CONNECT result code reports DTE spee
Disable protocol result codes.
(see also the “Result Code Options Table”)
W1
CONNECT result code reports DTE spee
Enable protocol result codes.
W2 *
CONNECT result code reports DCE spee
Enable protocol result codes.
Xn
Select result codes/call progress options
X0
Display CONNECT or “1” for all speeds.
Ignore dial tone and busy tone detection.
X1
Display connect message and the modem
data rate, and an indication of the modem
error correction and data compression.
Ignore dial tone and busy tone detection.
X2
Display connect message and the modem
data rate, and an indication of the modem
error correction and data compression.
Check dial tone before proceeding dialing,
ignore busy tone detection.
X3
Display connect message and the modem
data rate, and an indication of the modem
error correction and data compression.
Ignore dial tone before proceeding dialing,
check busy tone after making dialing.
X4 *
Display connect message and the modem
data rate, and an indication of the modem
error correction and data compression.
Check dial tone and busy tone.
X5
Same as X4.
X6
Same as X4.
X7
Display CONNECT or “1” for all speeds.
Check dial tone and busy tone.
Zn
Recall stored profile
Z0
Reset and recall user profile 0. Either Z0 or
Z1 restores the same single profile.
*
Manufacturer default
Extended “AT&” (Ampersand) Command Set
Command
Options
Function & Description
&Cn
Data carrier detect option
&C0
State of carrier from remote modem is
ignored. DCD circuit is always on
&C1 *
DCD turns on when the remote modem’s
carrier signal is detected, and off when the
carrier signal is not detected.
&Dn
Data Terminal Ready (DTR) option.
&D0
DTR ignored