TRENDnet TPL-410APK User's Guide - Page 56

Troubleshooting, Windows 7, Windows Vista, Windows XP/2000

Get TRENDnet TPL-410APK PDF manuals and user guides View all TRENDnet TPL-410APK manuals
Add to My Manuals
Save this manual to your list of manuals

Page 56 highlights

TRENDnet User's Guide Troubleshooting Q: I typed http://TPL-410AP in my Internet Browser Address Bar, but an error message says "The page cannot be displayed." How can I access the access point management page? Answer: Assign your computer a static IP address in the subnet of 192.168.10.x (ex. 192.168.10.25) and access the access point using the default IP address 192.168.10.100. http://192.168.10.100 Q: I typed http://192.168.10.100 in my Internet Browser Address Bar, but an error message says "The page cannot be displayed." How can I access the access point management page? Answer: 1. Check your hardware settings again. See "Basic Installation" on page 7. 2. Make sure the LAN port you are connected to is on. 3. Make sure your network adapter TCP/IP settings are set to Obtain an IP address automatically or DHCP (see the steps below). 4. Make sure your computer is connected to one of the access point's LAN ports 5. Press on the factory reset button for 15 seconds, the release. Windows 7 a. Go into the Control Panel, click Network and Sharing Center. b. Click Change Adapter Settings, right-click the Local Area Connection icon. c. Then click Properties and click Internet Protocol Version 4 (TCP/IPv4). d. Then click Obtain an IP address automatically and click OK. Windows Vista a. Go into the Control Panel, click Network and Internet. b. Click Manage Network Connections, right-click the Local Area Connection icon and click Properties. c. Click Internet Protocol Version (TCP/IPv4) and then click Properties. d. Then click Obtain an IP address automatically and click OK. Windows XP/2000 a. Go into the Control Panel, double-click the Network Connections icon b. Right-click the Local Area Connection icon and the click Properties. c. Click Internet Protocol (TCP/IP) and click Properties. d. Then click Obtain an IP address automatically and click OK. © Copyright 2014 TRENDnet. All Rights Reserved. TPL-410AP / TPL-410APK Note: If you are experiencing difficulties, please contact your computer or operating system manufacturer for assistance. Q: The Wizard does not appear when I access the access point. What should I do? Answer: 1. Click on Main and Wizard on the left hand side. 2. Near the top of the browser, "Pop-up blocked" message may appear. Right click on the message and select Always Allow Pop-ups from This Site. 3. Disable your browser's pop up blocker. Q: I cannot connect wirelessly to the access point. What should I do? Answer: 1. Double check that the Wireless LED on the access point is on. 2. Power cycle the router. Unplug the power to the access point. Wait 15 seconds, then plug the power back in to the access point. 3. Contact the manufacturer of your wireless network adapter and make sure the wireless network adapter is configured with the proper SSID. The default predefined SSID is printed on the device label on the bottom or on the sticker on the side of the unit. 4. To verify whether or not wireless is enabled, login to the access point management page, click on Basic and Wireless. 5. Please see "Steps to improve wireless connectivity" on page 18 if you continue to have wireless connectivity problems. 54

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
© Copyright 2014 TRENDnet. All Rights Reserved.
TRENDnet User’s Guide
TPL-410AP / TPL-410APK
54
Troubleshooting
Q: I typed http://TPL-410AP in my Internet Browser Address Bar, but an error message
says “The page cannot be displayed.” How can I access the access point management
page?
Answer:
Assign your computer a static IP address in the subnet of 192.168.10.x (ex.
192.168.10.25) and access the access point using the default IP address 192.168.10.100.
Q: I typed http://192.168.10.100 in my Internet Browser Address Bar, but an error
message says “The page cannot be displayed.” How can I access the access point
management page?
Answer:
1. Check your hardware settings again. See “
Basic Installation
” on page 7.
2. Make sure the LAN port you are connected to is on.
3. Make sure your network adapter TCP/IP settings are set to
Obtain an IP address
automatically
or
DHCP
(see the steps below).
4. Make sure your computer is connected to one of the access point’s LAN ports
5. Press on the factory reset button for 15 seconds, the release.
Windows 7
a. Go into the
Control Panel
, click
Network and Sharing Center
.
b. Click
Change Adapter Settings
, right-click the
Local Area Connection
icon.
c. Then click
Properties
and click
Internet Protocol Version 4 (TCP/IPv4)
.
d. Then click
Obtain an IP address automatically
and click
OK
.
Windows Vista
a. Go into the
Control Panel
, click
Network and Internet
.
b. Click
Manage Network Connections,
right-click the
Local Area Connection
icon and click
Properties
.
c. Click
Internet Protocol Version (TCP/IPv4)
and then click
Properties
.
d. Then click
Obtain an IP address automatically
and click
OK
.
Windows XP/2000
a. Go into the
Control Panel
, double-click the
Network Connections
icon
b. Right-click the
Local Area Connection
icon and the click
Properties
.
c. Click
Internet Protocol (TCP/IP)
and click
Properties
.
d. Then click
Obtain an IP address automatically
and click
OK
.
Note:
If you are experiencing difficulties, please contact your computer or
operating system manufacturer for assistance.
Q: The Wizard does not appear when I access the access point. What should I do?
Answer:
1. Click on Main and Wizard on the left hand side.
2. Near the top of the browser, “Pop-up blocked” message may appear. Right click on
the message and select Always Allow Pop-ups from This Site.
3. Disable your browser's pop up blocker.
Q: I cannot connect wirelessly to the access point. What should I do?
Answer:
1. Double check that the Wireless LED on the access point is on.
2. Power cycle the router. Unplug the power to the access point. Wait 15 seconds, then
plug the power back in to the access point.
3. Contact the manufacturer of your wireless network adapter and make sure the
wireless network adapter is configured with the proper SSID. The default predefined
SSID is printed on the device label on the bottom or on the sticker on the side of the
unit.
4. To verify whether or not wireless is enabled, login to the access point management
page, click on
Basic and Wireless
.
5. Please see “
Steps to improve wireless connectivity
” on page 18 if you continue to
have wireless connectivity problems.