Home » Thermador Manuals » Dishwashers » Thermador DWHD650WFP » Manual Viewer

Thermador DWHD650WFP Instructions for Use - Page 21

Unloading the dishwasher, RackMatic, Adjusting the height of the rack

View all Thermador DWHD650WFP manuals

Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

Unloading the dishwasher 9 CAUTION Dishes can be very hot immediately after cycle ends. Open the door slightly and allow dishes to cool for a few minutes before unloading. Note: Dishes are more likely to chip when unloading before cooling. When unloading the dishwasher, to prevent water from dripping onto dry dishes, unload the lower rack 9" first. Next, unload the silverware basket 1j followed by the upper rack 12, and then the third rack (if equipped). RackMatic® The height of the upper rack 12 can be adjusted in 3 steps to create more space for larger items in the lower rack. 1. Pull the upper rack out of the dishwasher until it stops. 2. To lower the rack, push the RackMatic® lever inward. 3. To raise the rack, hold the basket on the sides of the upper rack and lift it up. Adjusting the height of the rack *Adjustingheightoferack If required, the height of the upper rack 12 can be adjusted to create more space for taller utensils either in the upper or lower rack. With silverware basket Setting 1 max. ø Setting 2 max. ø Setting 3 max. ø Upper rack Lower rack 9.4 in (24 cm) 10.4 in (26.5 cm) 11.4 in (29 cm) 13.4 in (34 cm) 12 in (30.5 cm) 11 in (28 cm) With third rack Setting 1 max. ø Setting 2 max. ø Setting 3 max. ø Upper rack 7 in (18 cm) 8 in (20.5 cm) 9 in (23 cm) Lower rack 13.4 in (34 cm) 12 in (30.5 cm) 11 in (28 cm) Arrange large plates up to a diameter of 13.4 in (34 cm) in the lower basket 9" as illustrated. Note: Check spray arm for clearance after adjustment. * optional feature which may or may not be included with your dishwasher. 21

Section	Page
Table of contentsen-us Operating instructions	3
Safety Definitions	4
9 WARNING	4
9 CAUTION	4
NOTICE:	4
Note:	4
IMPORTANT SAFETY INSTRUCTIONS	5
READ AND SAVE THESE INSTRUCTIONS	5
To reduce the risk of fire, electrical shock, or serious injury, observe the following:Risk of fire, electrical shock, or serious injury	5
WARNING	5
Risk of injury or death	5
WARNING	5
Risk of injury	5
WARNING	5
Risk of electrical shock or fire	5
WARNING	5
Health hazard	5
GROUNDING INSTRUCTIONS	5
WARNING	5
Risk of electric shock	5
Safe Operation	5
CAUTION	5
WARNING	6
Risk of injury	6
Proper Care and Maintenance	6
WARNING	6
Risk of explosion	6
Note:	6
NOTICE:	6
State of California Proposition 65 Warning:	6
WARNING	6
Causes of Damage	7
NOTICES	7
Getting Started	8
Appliance overview	8
Operating panel	9
Note:	9
Dishwasher interior components	9
Display indicators	9
Menu Overview	10
Change the setting as follows:	10
1. Open the door.	10
2. Press the ON/OFF button (.	10
3. Press and hold the ‹button for 3 seconds until •:‹... is shown on the display window H	10
4. Press the ‹button to access the individual settings.	10
5. Adjust the setting using the + and - buttons. P.	10
6. Press and hold the ‹button for 3 seconds.	10
Note:	10
Home Connect™	11
Wi-Fi \|	11
Activate Wi-Fi:	11
1. Press the on ON/OFF button (.	11
2. Press and hold the button ‹ for 3 seconds.	11
3. Press the button ‹ repeatedly until ’Ÿ:‹‹ appears in the display window H.	11
4. Use the setting button + P to activate Wi-Fi ’Ÿ:‹‚.	11
5. Press and hold the button ‹ for 3 seconds.	11
Note:	11
Network login	11
Connect dishwasher to home network and app:	11
1. Switch on ON/OFF switch (.	11
2. Press and hold the button ‹ for 3 seconds.	11
3. Press the button ‹ repeatedly until H ‘’ or †‘ appears in the display window.	11
4. Start connection with the setting button + P.	11
Note:	11
Connect to the app	11
Note:	11
Connect dishwasher to app:	11
1. Switch on ON/OFF switch (.	11
2. Press and hold the button ‹ for 3 seconds.	11
3. Press the button ‹ repeatedly until ‘˜:˜ appears in the display window H.	11
4. Start connection with the setting button + P.	11
Note:	11
Remote start button	12
Notes	12
Wi-Fi without a connection to the Home Connect server ƒWi-Fi without a connection to the Home Connect server	12
Note:	12
Remote diagnostics	12
Note:	12
Water softening system / special salt *	13
Adjusting the water softener settings	13
Using the test strip included with your dishwasher (Purchased test strips may have a different scale)	13
Water softener setting	13
Add salt to salt dispenser	13
Water hardness	13
°E value	13
mmol/l	13
Adjusting the water softening system	13
Set the softening system as follows:	13
1. Ask your local water utility company for the water hardness value of the tap water.	13
2. Required setting can be found in the water hardness table.	13
3. Open the door.	13
4. Press the ON/OFF button (.	13
5. Press the Setup button for 3 seconds until •:‹‹ is shown on the display window H.	13
6. Make the selection with setting buttons + - P.	13
7. Press and hold the Setup button for 3 seconds.	13
Using special salt	13
NOTICE:	13
Top off the salt as follows:	13
1. Undo the screw plug on the dispenser 1Z.	13
2. Fill the dispenser with water (required only when switching on the appliance for the first time).	13
3. Add salt as illustrated (do not use table salt or tablets).	13
Using detergents with salt componentDetergent with a salt component	14
Switching off low salt indicator / water softening systemSwitching off water softening system	14
Rinse Aid	15
Adding rinse aid	15
NOTICE:	15
1. Open the rinse aid dispenser 9* by pressing on the latch of the lid and pulling it open.	15
2. Add liquid rinse aid to the dispenser 9* until it is full. Do not overfill. Avoid spilling into air vent hole.	15
3. Close the lid. Lid must be fully closed until it clicks in order to seal.	15
4. Wipe up any excess rinse aid that may have puddled when the dispenser reservoir is full.	15
Tip:	15
NOTICE:	15
Setting the amount of rinse aid used	15
Set the amount of rinse aid as follows:	15
1. Open the door.	15
2. Press on ON/OFF button (.	15
3. Press the Setup button for 3 seconds until •:‹‹ is shown on the display window H.	15
4. Keep pressing the Setup button until the rinse aid setting, §:‹† is displayed.	15
5. Change the setting with the setting buttons + - P.	15
6. Press and hold the Setup button for 3 seconds.	15
Note:	15
Turning off rinse aid indicator	15
NOTICE:	15
Loading the Dishwasher	16
Dishware material	16
Note:	16
Loading the racks	16
NOTICE:	16
Loading the upper rack	16
Note:	16
Loading the lower rack	16
Suggested loading pattern	17
10 place setting	17
Lower rack 9\	17
Upper rack 12	17
Note:	17
Third rack 1*	17
Additional loading pattern	17
12 place setting	17
Lower rack 9\	17
Upper rack 12	17
Note:	17
Third rack 1*	17
Loading the silverware basket	18
9 WARNING	18
Risk of injury	18
Long silverware basket *	18
Note:	18
Loading patterns silverware basket	18
Suggested loading pattern - 10 place setting	18
Additional loading pattern - 12 place setting	18
The Double Flex silverware basket *	19
Side by side	19
Back to back	19
Note:	19
Loading patterns silverware basket	19
Suggested loading pattern - 10 place setting	19
Additional loading pattern - 12 place setting	20
Alternate loading patterns	20
Loading large items in the lower rack	20
Alternate loading pattern with pots and pans	20
Loading stemware in the upper rack	20
Alternate loading pattern with stemware	20
Unloading the dishwasher	21
9 CAUTION	21
Note:	21
RackMatic®	21
1. Pull the upper rack out of the dishwasher until it stops.	21
2. To lower the rack, push the RackMatic® lever inward.	21
3. To raise the rack, hold the basket on the sides of the upper rack and lift it up.	21
Note:	21
Adjusting the height of the rack *Adjusting the height of the rack	21
9.4 in (24 cm)	21
13.4 in (34 cm)	21
10.4 in (26.5 cm)	21
12 in (30.5 cm)	21
11.4 in (29 cm)	21
11 in (28 cm)	21
7 in (18 cm)	21
13.4 in (34 cm)	21
8 in (20.5 cm)	21
12 in (30.5 cm)	21
9 in (23 cm)	21
11 in (28 cm)	21
Rack accessories	22
Flip tines*	22
Fold down the flip tines as follows:	22
1. Pull flip tine gently forward and release it from the notch (1).	22
2. Push the flip tine downward to the desired position (2).	22
Third rack	22
Plastic item clips*	22
Cup shelves*	22
Extra tall item sprinkler*	23
Note:	23
NOTICE:	23
Removing/Installing third rack	24
Removing third rack 1*	24
1. Pull out third rack all the way (1).	24
2. Lift upper rollers over the stopper hooks of both rails (2).	24
3. Pull third rack out forward and upward so that the holding hooks and the lower rollers of the rack slide over the stopper hooks of both rails (3).	24
Installing third rack 1*	24
1. Pull out third rack rails all the way (1).	24
2. Insert third rack at an angle. Make sure that the stopper hooks of both rails slide in between the holding hooks and the lower rollers of the third rack (2).	24
3. Slide third rack in and lift the upper rollers over the front stopper hooks of both rails (3).	24
4. Push in third rack (4).	24
Removing/Installing upper rack with Rackmatic®	25
Removing upper rack 12	25
1. Pull out upper rack all the way (1).	25
2. Lift front rollers over the stopper hook of the rail (2).	25
3. Pull out upper rack forwards and upwards so that the upper and lower rollers of the rack slide over the stopper hooks of both rails (3).	25
Installing upper rack 12	25
1. Pull out upper rack rails all the way (1).	25
2. Insert upper rack at an angle. Make sure that the stopper hooks of both rails slide in between the upper and lower rollers on the rear side of the rack (2).	25
3. Slide upper rack in and lift the upper rollers over the front stopper hooks of both rails (3).	25
4. Push in upper rack (4).	25
Detergent	26
NOTICE:	26
Note:	26
Adding detergent	26
1. If the detergent dispenser 92 is still closed, push the button 9: to open it.	26
Note:	26
2. When using detergent tabs, lay them such that they do not come in contact with the cover, insert a detergent tab flat, not on its side.	26
Note:	26
3. Close the lid by placing the finger on the lid as shown. Slide the lid closed and press down firmly until it clicks.	27
Tip:	27
Dishwasher Cycles	28
Note:	28
Note:	28
Dishwasher Cycle Options	29
PowerBoost ®	29
Half Load	29
Sanitize	29
Extra Dry	29
Wash Cycle Information	30
Note:	30
Operating the Dishwasher	31
Note:	31
9 WARNING	31
Risk of injury	31
Protection against unintentional operation	31
Note:	31
Operating the touch buttons	31
Changing the settings	31
Here’s how to change the settings:	31
1. Switch on ON/OFF switch (.	31
2. Press and hold the ‹ button for 3 seconds.	31
3. Press the ‹ button to access the individual settings.	31
4. Adjust the setting using the buttons - and + P.	31
5. Press and hold the ‹ button for 3 seconds.	31
AquaSensor	31
Sensor setting	31
Time display	31
Delay Start	32
1. Open the door and press the On/Off button (. Select a cycle.	32
2. Press the Delay button from the wash cycle options h until the displayed time corresponds with your requirements.	32
3. Press the Start button )\	32
1. Open the door and press the Delay button until œ:‹‹ is indicated on the digital display H.	32
2. Press the Start button )\	32
Wash cycle end	32
Auto power off	32
Possible settings are:	32
Switching off the appliance	32
Short time after the end of the wash cycle:	32
1. Open the door.	32
2. Switch off On/Off button (.	32
3. Turn off water supply.	32
4. Remove the utensils when they have cooled down.	32
9 WARNING	32
Risk of injury	32
Interrupting the wash cycle	32
9 CAUTION	32
1. Open the door.	32
2. Switch off On/Off switch (.	32
3. To continue the wash cycle, switch on the On/Off switch ( again.	32
4. Close the door.	32
Note:	32
Cancel a cycle (Reset)	32
1. Open the door and press and hold Start button )\	32
2. Wait about 1 minute while the dishwasher drains.	32
3. Open the door and press the On/Off button (.	32
Changing the wash cycle	33
Intensive drying	33
InfoLight® *	33
Time Remaining Power Beam® (Optical display while the wash cycle is running) *	33
Care and Maintenance	34
Cleaning the dishwasher	34
NOTICES	34
9 WARNING	34
Filters	34
Filter components	34
The filter system 1b consists of three parts.	34
Cleaning intervals	34
Note:	35
To check or clean the filter system:	35
1. After each wash cycle check the filters for residue.	35
2. Unscrew the Large Object Trap as illustrated and remove the entire filter system.	35
3. Remove the microfilter from the fine filter for easier cleaning.	35
4. Rinse the filters under running water and use a soft brush to clean.	35
Note:	35
5. Reinstall the filter system in reverse sequence and lock into place by screwing the Large Object Trap until the marking arrows align.	35
Spray arms	35
1. Check outlet nozzles on the spray arms for blockages.	35
2. Unscrew the upper spray arm 1: (1) and remove downwards (2).	35
3. Remove the lower spray arm 1R upwards.	35
4. Clean spray arms under running water.	35
5. Re-engage or screw on spray arms.	35
Drain pump	36
9 WARNING	36
1. Disconnect the appliance from the power supply.	36
2. Take out upper rack 12 and lower rack 9\	36
3. Remove the filters 1b.	36
4. Scoop out standing water - use a sponge if necessary.	36
5. Using a spoon, pry off the pump cover (as shown) until it clicks, then grip the cover and pull upward until it resists and then pull forward (1). Remove cover completely.	36
6. Check inner compartment and remove any foreign objects.	36
7. Place pump cover in the original position (2) and press down until it engages (3).	36
8. Place cover in the original position, press down and engage.	36
9. Reinstall filters.	36
10. Re-insert racks.	36
Note:	36
Preparing your unit for vacation	36
NOTICE:	36
Winterizing your unit	36
NOTICE:	36
Troubleshooting	37
Note:	37
9 WARNING	37
Improper repairs or use of non-original replacement parts may cause considerable damage and put the user at considerable risk	37
Error message	37
Fault table	37
Customer Service	42
1. Contact your installer or the Thermador® authorized service provider in your area.	42
2. E-mail us from the customer service section of our website, www.thermador.com (USA) or www.thermador.ca (Canada)	42
3. Call us at 800-735-4328	42
4. Write us:	42
Statement of Limited Product Warranty	43
What this Warranty Covers & Who it Applies to:	43
How Long the Warranty Lasts	43
Extended Limited Warranty	43
Repair/Replace as Your Exclusive Remedy	43
Out of Warranty Product	43
Warranty Exclusions	44
How to Obtain Warranty Service	44
Table des matièresfr-ca Notice d'utilisation	45
Indications de sécurité	46
9 AVERTISSEMENT	46
9 ATTENTION	46
AVIS :	46
Remarque :	46
CONSIGNES DE SÉCURITÉ IMPORTANTES	47
LISEZ ET CONSERVEZ CES INSTRUCTIONS	47
Pour réduire le risque d'incendie, de choc électrique, ou de blessures graves, respectez les consignes suivantes :Risque d'incendie, de choc électrique, ou de blessures graves	47
AVERTISSEMENT	47
Risque de blessure ou de décès	47
AVERTISSEMENT	47
Risque de blessures	47
AVERTISSEMENT	47
Risque de choc électrique ou d'incendie	47
AVERTISSEMENT	47
Risque pour la santè	47
INSTRUCTIONS DE MISE À LA TERRE	47
AVERTISSEMENT	47
Risque de choc électrique	47
Fonctionnement normal	47
ATTENTION	47
AVERTISSEMENT	48
Risque de blessures	48
Entretien et maintenance corrects	48
AVERTISSEMENT	48
Risque d’explosion	48
Remarque :	48
AVIS :	48
Avertissement issue de la proposition 65 de l’État de la Californie :	48
AVERTISSEMENT	48
Causes de pannes	49
AVIS	49
Mise en marche	50
Vue d'ensemble de l'appareil	50
Panneau de commande	51
Remarque :	51
Composants internes du lave-vaisselle	51
Indicateurs	51
Aperçu du menu	52
Changez les réglages comme suit :	52
1. Ouvrez la porte.	52
2. Appuyez sur le bouton On/Off (Marche/Arrêt) (.	52
3. Appuyez sur la touche ‹ durant 3 secondes jusqu'à ce que •:‹... soit affiché dans l'écran supérieur H	52
4. Appuyez sur le bouton Start ‹ pour enregistrer le réglage individuel.	52
5. Ajustez le réglage avec les boutons + et -. P.	52
6. Appuyez et maintenez la touche ‹ enfoncée pendant 3 secondes.	52
Remarque :	52
Home Connect™	54
Wi-Fi \|	54
Activer le Wi-Fi :	54
1. Appuyez sur le bouton On/Off (Marche/Arrêt) (.	54
2. Appuyez et maintenez la touche ‹ enfoncée pendant 3 secondes.	54
3. Appuyer sur la touche ‹ à plusieurs reprises jusqu'à ce que ’ Ÿ‹ ou ‹H s'affiche à l'écran.	54
4. Utilisez le bouton + P pour activer le Wi-Fi ’Ÿ:‹‚.	54
5. Appuyez et maintenez la touche ‹ enfoncée pendant 3 secondes.	54
Remarque :	54
Network login (connexion au réseau)	54
Brancher votre lave-vaisselle à votre réseau domestique et à l'application :	54
1. Appuyez sur le bouton ON/OFF (MARCHE/ARRÊT) (.	54
2. Appuyez et maintenez la touche ‹ enfoncée pendant 3 secondes.	54
3. Appuyer sur la touche ‹ à plusieurs reprises jusqu'à ce que H ‘’ ou †‘ s'affiche à l'écran.	54
4. Lancez la connexion avec le bouton de réglage + P.	54
Remarque :	54
Connect to the app (se connecter à l'application)	54
Remarque :	54
Brancher votre lave-vaisselle à votre réseau domestique et à l'application :	54
1. Appuyez sur le bouton ON/OFF (MARCHE/ARRÊT) (.	54
2. Appuyez et maintenez la touche ‹ enfoncée pendant 3 secondes.	54
3. Appuyer sur la touche ‹ à plusieurs reprises jusqu'à ce que ‘˜ ˜ ou s'affiche à l'écran H.	54
4. Lancez la connexion avec le bouton de réglage + P.	54
Remarque :	54
Bouton de télédémarrage	55
Remarques	55
Wi-Fi sans connexion au serveur Home Connect ƒWi-Fi sans connexion au serveur Home Connect	55
Remarque :	55
Diagnostics à distance	55
Remarque :	55
Système d'adoucissement de l'eau / sels *	56
Réglage des paramètres d'adoucissement de l'eau	56
Utiliser la bandelette d'analyse comprise avec votre lave-vaisselle (les bandelettes d'analyse achetées séparément pourraient avoir une échelle différente)	56
Réglage de l'adoucisseur d'eau	56
Ajouter du sel au distributeur de sel	56
Dureté de l'eau	56
Valeur E	56
mmol/l	56
Réglage du système d'adoucissement de l'eau	56
Réglez le système d'adoucissement comme suit :	56
1. Demandez le degré de dureté de votre eau courante à votre fournisseur d'eau.	56
2. Le réglage à effectuer se trouve dans le tableau de dureté de l'eau.	56
3. Ouvrez la porte.	56
4. Appuyez sur le bouton On/Off (Marche/Arrêt) (.	56
5. Appuyez sur la touche Setup durant 3 secondes jusqu'à ce que •:‹‹ soit affiché dans l'écran supérieur H.	56
6. Effectuez le réglage à l'aide des boutons + - P.	56
7. Appuyez et maintenez la touche Setup enfoncée pendant 3 secondes.	56
Utilisation des sels spéciaux	56
AVIS :	56
Remplissez les sels comme suit :	56
1. Retirez le bouchon à vis du distributeur 1Z.	56
2. Remplissez le distributeur d'eau (opération requise uniquement lors de la première mise sous tension de l'appareil).	56
3. Ajoutez les sels tel qu'illustré (n'utilisez pas de sel de table ou de comprimés).	56
Utilisation de détergents chargés en selsDétergent chargé en sels	57
Éteindre l'indicateur de niveau bas de sels/le système d'adoucissement de l'eauÉteindre le système d'adoucissement de l'eau	57
Produit de rinçage	58
Ajout d'agent de rinçage	58
AVIS :	58
1. Ouvrez le distributeur de liquide de rinçage 9* en appuyant sur le loquet du couvercle et en tirant sur celui-ci.	58
2. Remplissez le distributeur 9* de produit de rinçage liquide jusqu'à pleine capacité. Il ne doit pas déborder. Évitez tout déversement dans le trou d'aération.	58
3. Fermez le couvercle. Le couvercle doit être hermétiquement fermé jusqu'à l'encliquetage du loquet, pour garantir son étanchéité.	58
4. Essuyez tout excédent de produit de rinçage déversé lorsque le réservoir est plein.	58
Conseil :	58
AVIS :	58
Réglage de la quantité de produit de rinçage utilisé	58
Réglez la quantité d'agent de rinçage comme suit :	58
1. Ouvrez la porte.	58
2. Appuyez sur le bouton ON/OFF (MARCHE/ARRÊT) (.	58
3. Appuyez sur la touche Setup durant 3 secondes jusqu'à ce que •:‹‹ soit affiché dans l'écran supérieur H.	58
4. Continuez d'appuyer sur le bouton Setup jusqu'à ce que s'affiche le réglage d'agent de rinçage, §:‹†.	58
5. Changez le réglage avec les boutons + - P.	58
6. Appuyez et maintenez la touche Setup enfoncée pendant 3 secondes.	58
Remarque :	58
Désactivation de l'indicateur de produit de rinçage	58
AVIS :	58
Chargement du lave-vaisselle	59
Matériaux lavables au lave-vaisselle	59
Remarque :	59
Chargement des paniers	59
AVIS :	59
Chargement du panier supérieur	59
Remarque :	59
Chargement du panier inférieur	59
Configuration de chargement suggérée	60
Réglage 10 places	60
Panier inférieur 9\	60
Panier supérieur 12	60
Remarque :	60
Troisième panier 1*	60
Configuration de chargement supplémentaire	60
Réglage 12 places	60
Panier inférieur 9\	60
Panier supérieur 12	60
Remarque :	60
Troisième panier 1*	60
Chargement du panier à ustensiles	61
9 AVERTISSEMENT	61
Risque de blessures	61
Paniers à ustensiles longs *	61
Remarque :	61
Profils de chargement du panier à ustensiles	61
Configuration de chargement suggérée - réglage 10 places	61
Configuration de chargement suggérée - réglage 12 places	61
Le panier à ustensiles Double Flex *	62
Côte à côte	62
Dos à dos	62
Remarque :	62
Profils de chargement	62
Configuration de chargement suggérée - réglage 10 places	63
Configuration de chargement supplémontaire - réglage 12 places	63