Thermador DWHD650WFP Instructions for Use - Page 38

Fault, Cause, Remedial action

Get Thermador DWHD650WFP PDF manuals and user guides View all Thermador DWHD650WFP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

Fault Dishes not dry. Cause Remedial action No or too little rinse aid in the dis- Refill rinse aid. penser. Wash cycle selected without drying. Select wash cycle with drying. Water collecting in depressions on Arrange dishes in a sloping position, arrange the dishes and silverware. affected dishes as sloping as possible. Plastic dishes not dry. Silverware not dry. Appliance interior wet after rinse cycle. Food soils on the dishes. The combined detergent used has a Use different combination detergent with better poor drying performance. drying performance. Use of rinse aid also increases the drying performance. extraDry to increase drying not acti- Activate extraDry. vated. Dishes were removed too early or Wait until wash cycle ends or wait until 30 min drying process had not ended yet. after wash cycle ends before removing dishes. The eco rinse aid used has a limited Use a commercial brand of rinse aid. Eco drying performance. products may have limited effectiveness. Special properties of plastic. Plastics do not dry well because they do not hold heat. Silverware not arranged properly in Separate silverware if possible, prevent con- the silverware basket. tact points. Silverware not arranged properly in Arrange silverware properly and separate if the third rack. possible. No appliance fault. Dishwashers us "condensation drying," where humid air condenses on tub walls so it can drain and be pumped out. Dishes placed too closely together, Arrange dishes with adequate clearance racks overfilled. between them ensuring that the spray jets can reach the surface of the dishes. Prevent con- tact points. Spray arm rotation obstructed. Arrange dishes so that the spray arm can rotate without obstruction. Spray arm nozzles are blocked. Clean the spray arm nozzles. Filters 1b dirty. Clean filters. Filters 1b inserted incorrectly and/ Insert and engage filters correctly. or not engaged. Rinse wash cycle too weak. Select a more intensive rinse cycle. Increase sensitivity of the sensors. Dishes precleaned too intensely; sensors therefore decide on weak wash cycle sequence. Stubborn soiling cannot be completely removed. Do not prerinse dishes. Remove only large food soils. Increase sensitivity of the sensors. Recommended wash cycle "Regular" or Intensive. Tall narrow containers in corner areas are not rinsed adequately. Do not tilt containers and do not place in the corner area. Upper rack 12 on right and left not set to same height. Set upper rack to same height using side levers. 38

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
38
Dishes not dry.
No or too little rinse aid in the dis-
penser.
Refill rinse aid.
Wash cycle selected without drying.
Select wash cycle with drying.
Water collecting in depressions on
the dishes and silverware.
Arrange dishes in a sloping position, arrange
affected dishes as sloping as possible.
The combined detergent used has a
poor drying performance.
Use different combination detergent with better
drying performance. Use of rinse aid also
increases the drying performance.
extraDry to increase drying not acti-
vated.
Activate extraDry.
Dishes were removed too early or
drying process had not ended yet.
Wait until wash cycle ends or wait until 30 min
after wash cycle ends before removing dishes.
The eco rinse aid used has a limited
drying performance.
Use a commercial brand of rinse aid. Eco
products may have limited effectiveness.
Plastic dishes not dry.
Special properties of plastic.
Plastics do not dry well because they do not
hold heat.
Silverware not dry.
Silverware not arranged properly in
the silverware basket.
Separate silverware if possible, prevent con-
tact points.
Silverware not arranged properly in
the third rack.
Arrange silverware properly and separate if
possible.
Appliance interior wet after
rinse cycle.
No appliance fault.
Dishwashers us “condensation drying,” where
humid air condenses on tub walls so it can
drain and be pumped out.
Food soils on the dishes.
Dishes placed too closely together,
racks overfilled.
Arrange dishes with adequate clearance
between them ensuring that the spray jets can
reach the surface of the dishes. Prevent con-
tact points.
Spray arm rotation obstructed.
Arrange dishes so that the spray arm can
rotate without obstruction.
Spray arm nozzles are blocked.
Clean the spray arm nozzles.
Filters
1b
dirty.
Clean filters.
Filters
1b
inserted incorrectly and/
or not engaged.
Insert and engage filters correctly.
Rinse wash cycle too weak.
Select a more intensive rinse cycle.
Increase sensitivity of the sensors.
Dishes precleaned too intensely;
sensors therefore decide on weak
wash cycle sequence. Stubborn
soiling cannot be completely
removed.
Do not prerinse dishes. Remove only large
food soils.
Increase sensitivity of the sensors.
Recommended wash cycle "Regular" or Inten-
sive.
Tall narrow containers in corner
areas are not rinsed adequately.
Do not tilt containers and do not place in the
corner area.
Upper rack
12
on right and left
not set to same height.
Set upper rack to same height using side
levers.
Fault
Cause
Remedial action