Home » Thermador Manuals » Ovens » Thermador PODM301J » Manual Viewer

Thermador PODM301J Installation Instructions - Page 3

Safety - handles

Add to My Manuals
Save this manual to your list of manuals

Page 3 highlights

Safety Important Safety Instructions READ AND SAVE THESE INSTRUCTIONS WARNING: If the information in this manual is not followed exactly, fire or shock may result causing property damage or personal injury. WARNING: Do not repair or replace any part of the appliance unless specifically recommended in the manuals. Improper installation, service or maintenance can cause injury or property damage. Refer to this manual for guidance. All other servicing should be done by a qualified technician. Appliance Handling Safety Do not lift appliance by door handle. Remove the door for easier handling and installation. See instructions in Use and Care Manual. Unit is heavy and requires at least two people or proper equipment to move. Hidden surfaces may have sharp edges. Use caution when reaching behind or under appliance. Safety Codes and Standards This appliance complies with one or more of the following Standards: • UL 858, The Standard for the Safety of Household Electric Ranges • UL 923, The Standard for the Safety of Microwave Cooking Appliances • UL 507, The Standard for the Safety of Electric Fans • ANSI Z21.1, The American National Standard for Household Cooking Gas Appliances • CAN/CSA-C22.2 No. 113-M1984 Fans and Ventilators • CAN/CSA-C22.2 No. 61-M89 Household Cooking Ranges It is the responsibility of the owner and the installer to determine if additional requirements and/or standards apply to specific installations. Electric Safety Before you plug in an electrical cord, be sure all controls are in the OFF position. If required by the National Electrical Code (or Canadian Electrical Code), this appliance must be installed on a separate branch circuit. Installer - show the owner the location of the circuit breaker or fuse. Mark it for easy reference. Important - Save these instructions for the local electrical inspector's use. Before installing, turn power OFF at the service panel. Lock service panel to prevent power from being turned ON accidentally. Refer to data plate for more information. See "Data Plate" under "Service" for data plate location. Be sure your appliance is properly installed and grounded by a qualified technician. Installation, electrical connections and grounding must comply with all applicable codes. Related Equipment Safety Remove all tape and packaging before using the appliance. Destroy the packaging after unpacking the appliance. Never allow children to play with packaging material. Never modify or alter the construction of the appliance. For example, do not remove leveling legs, panels, wire covers or anti-tip brackets/screws. English 1

Section	Page
INSTALLATION MANUAL	1
Built-in Ovens	1
Safety 1	2
Important Safety Instructions 1	2
Preparation 2	2
Before you Begin 2	2
Dimensions for 27” Wall-Mounted Units 3	2
Dimensions for 27” under the counter 4	2
Dimensions for 30” Wall-Mounted Units 6	2
Dimensions for 30” under the counter 8	2
Removing Packaging 9	2
Installation 12	2
Electrical Installation 12	2
Oven Installation 13	2
Testing Operation 14	2
Service 14	2
Safety	3
Important Safety Instructions	3
Read and save these instructions	3
Appliance Handling Safety	3
Safety Codes and Standards	3
Electric Safety	3
Related Equipment Safety	3
Transport	4
Preparation	4
Before you Begin	4
Tools and Parts Needed	4
Parts Included	4
General Information	4
Power Requirements	4
Dimensions for 27” Wall-Mounted Units	5
Single Oven 27”	5
Note:	5
Double Oven 27”	5
Note:	5
Combo Oven with Microwave and Warming Drawer 27”	6
27” Under-the-counter units	6
Dimensions for 30” Wall-Mounted Units	8
Single Oven 30”	8
Note:	8
Double Oven 30”	8
Note:	8
Combo Oven with Microwave 30”	9
Note:	9
Combo Oven with Microwave and Warming Drawer 30”	9
Note:	9
Dimensions for 30” Under-the-counter- Units	10
Removing Packaging	11
Left Packaging Bracket Removal	11
Right Packaging Bracket Removal	11
Note:	11
For Convection Microwave Combination Units (for Convection Microwave Combination Units Only)	12
Preparing Oven	12
Microwave Combination Units Adjustment Feature	13
Installation	14
Electrical Installation	14
25 AMP	14
30 AMP	14
30 AMP	14
40 AMP	14
50 AMP	14
Electrical Connection	14
Oven Installation	15
Note:	15
1. Be sure to read the above CAUTION before attempting to remove the door.	15
2. Open the door completely.	15
3. Flip levers on hinges toward you.	15
4. Holding the door firmly on both sides and using both hands, close the door gently until it stops against the levers, about 30º from the closed position.	15
5. Carefully lift the door up and out of the hinge slots. Hold firmly; the door is heavy.	15
6. Place the door in a convenient and stable location for cleaning.	15
Installing the Oven	15
1. Lift or slide unit into cabinet cutout. Do not lift appliance by door handle.	15
2. Push straight in until oven trim is flush with cabinet wall, being careful not to crimp flexible conduit between oven and cabinet back wall. The oven should be straight and level, not crooked.	15
3. Install supplied screws through tap holes in trim. (2 screws for single ovens, 4 screws for double/combo ovens)	15
1. Hold the door firmly in both hands.	16
2. Hold the door at a 30º angle from the closed position and insert hinges into the slots. You may need to rock the door forward and backward slightly to seat the hinge feet.	16
3. The door may need to be removed and re- inserted until the hinges sit correctly in the slots.	16
4. Open door all the way to expose hinges, levers, and slots.	16
5. Push levers foreward and down until seated on the bracket.	16
6. Close and open door slowly to be sure it is correctly and securely in place. Door must be straight, not crooked.	16
Testing Operation	16
1. Turn on power at the breaker.	16
2. Test the oven mode.	16
3. Verify that the oven light comes on and the oven begins to preheat.	16
4. Test the door lock.	16
5. If installing a double oven, test the second oven as well.	16
6. If any of the tests do not result as explained above, contact Thermador service for assistance. Otherwise, the installation is complete at this time.	16
Service	16
Before Calling Service	16
Data Plate	16
Sécurité 1	17
Consignes de sécurité importantes 1	17
Préparation 3	17
Avant de commencer 3	17
Appareils électroménagers de 27 po 4	17
Dimensions pour dessous d’armoire de 27 po 6	17
Appareils électroménagers de 30 po 7	17
Dimensions pour dessous d’armoire de 30 po 9	17
Pour enlever l’emballage 11	17
Installation 13	17
Installation électrique 13	17
Installation du four 15	17
Test de contrôle 16	17
Dépannage 16	17
Sécurité	18
Consignes de sécurité importantes	18
Lire et conserver ces consignes	18
Sécurité de manipulation de l'appareil	18
Codes et normes de sécurité	18
Sécurité électrique	18
Sécurité apparentée concernant l'équipement	18
Transport	19
Préparation	20
Avant de commencer	20
Outils et pièces nécessaires	20
Pièces incluses	20
Informations générales	20
Exigences électriques	20
La prise doit être correctement reliée à la terre selon tous les codes applicables.	20
Four unique de 27 po	21
Fours doubles de 27 po	21
Four combiné avec micro-ondes et tiroir- réchaud de 27 po	22
Appareils de 27 po montés sous le plan de travail	22
Four unique de 30 po	24
Fours doubles de 30 po	24
Four combiné avec micro-ondes de 30 po	25
Four combiné avec micro-ondes et tiroir- réchaud d 30 po	25
Appareils de 30 po montés sous le plan de travail	26
Pour enlever l’emballage	28
Installation	30
Installation électrique	30
Raccordement électrique	31
Installation du four	32
1. S'assurer de lire l'encart \	32
2. Ouvrir la porte complètement.	32
3. Basculer les leviers des charnières vers soi.	32
4. Fermer la porte doucement jusqu'à ce qu'elle se bloque. Elle se ferme environ à mi-chemin.	32
5. Tenir fermement la porte par les côtés avec les deux mains, tirer tout droit vers le haut hors des fentes de charnières et la sortir. Maintenir fermement, la porte est lourde.	32
6. Placer la porte dans un endroit pratique et stable pour le nettoyage.	32
Installation du four	32
1. Faites glisser l’appareil à l’endroit prévu de l’installation. Ne soulevez pas l’appareil par la poignée de la porte.	32
2. Le pousser droit jusqu’à ce qu’il soit à égalité avec le mur de l’armoire en faisant attention à ne pas coincer le conduit flexible entre le four et la paroi arrière de l’armoire. Le four doit être droit et non croche.	32
3. Fixez les vis fournies à travers les trous de mise en perce de la bordure. (2 vis pour les fours simples, 4 vis pour les fours doubles/combos)	32
1. Tenir la porte fermement avec les deux mains.	33
2. Tenir la porte à un angle de 30° de la position fermée et insérer les charnières dans les fentes. Il faudra peut-être faire basculer légèrement la porte, avant et arrière, pour bien mettre en place.	33
3. Il faudra peut-être enlever la porte et la remettre jusqu’à ce que les charnières soient bien en place dans les fentes	33
4. Ouvrir la porte complètement pour exposer les charnières, leviers et fentes.	33
5. Pousser les leviers vers l’avant jusqu’à ce qu’ils soient bien en place dans la fixation.	33
6. Fermer et ouvrir la porte lentement pour s’assurer qu’elle est bien installée. Elle doit être droite et non croche.	33
Test de contrôle	33
1. Mettre l’alimentation en circuit au coupe-circuit.	33
2. Vérifier le mode four.	33
3. Vérifier si l’éclairage du four s’allume et que le four commence à préchauffer.	33
4. Vérifier le verrouillage de porte.	33
5. Pour un four double, vérifier le second four.	33
6. Si les vérifications ne donnent pas les résultats escomptés, communiquer avec le service Thermador pour de l’aide. Autrement, l’installation est complétée.	33
Dépannage	33
Avant d'appeler le service de dépannage	33
Plaque signalétique	33
Seguridad 1	34
Instrucciones de seguridad importantes 1	34
Instalación 3	34
Antes de empezar 3	34
Electrodomésticos de 27\	34
Dimensiones para 27\	34
Electrodomésticos de 30\	34
Dimensiones para 30\	34
Quitar el embalaje 11	34
Instalación 13	34
Instalación eléctrica 13	34
Instalar el horno 15	34
Probar el equipo 16	34
Servicio 17	34
Seguridad	35
Instrucciones de seguridad importantes	35
Lea y conserve estas instrucciones	35
Seguridad con el manejo del electrodoméstico	35
Códigos y normas de seguridad	35
Seguridad con la electricidad	35
Seguridad de los equipos relacionados	36
Transporte	36
Instalación	37
Antes de empezar	37
Herramientas y piezas necesarias	37
Piezas incluidas	37
Información general	37
Requisitos de electricidad	37
Electrodomésticos de 27	38
Horno individual de 27\	38
Hornos dobles de 27\	38
Horno combinado con microondas y cajón calentador de 27\	39
Unidades instaladas debajo de la superficie de trabajo de 27\	39
Electrodomésticos de 30\	41
Horno individual de 30\	41
Hornos dobles de 30\	41
Horno combinado con microondas de 30\	42
Horno combinado con microondas y cajón calentador de 30\	42
Unidades instaladas debajo de la superficie de trabajo de 30\	43
Quitar el embalaje	45
Instalación	47
Instalación eléctrica	47
Conexión eléctrica	48
Instalar el horno	49
1. Asegúrese de leer la PRECAUCIÓN anterior antes de intentar retirar la puerta.	49
2. Abra la puerta por completo.	49
3. Lleve las palancas de las bisagras hacia usted.	49
4. Cierre la puerta con cuidado hasta que se detenga. Se cerrará hasta la mitad aproximadamente.	49
5. Sujetando la puerta firmemente de ambos lados, con las dos manos, jale la puerta hacia arriba y sáquela de las ranuras de las bisagras. Sujétela con firmeza; la puerta es pesada.	49
6. Coloque la puerta en un lugar práctico y estable para limpiarla.	49
Instalar el horno	50
1. Instale el equipo hacia el lugar en que se instalará. No sujete el equipo por la palanca de la puerta.	50
2. Empuje el horno hacia atrás hasta que el borde quede al ras con la pared del gabinete. Tenga cuidado para no doblar el conducto flexible entre el horno y la pared trasera del gabinete. El horno debe quedar en posición recta, no torcida.	50
3. Instale les tornillos proporcionados à través de los agujeros preperforados del adorno. (2 tornillos para los hornos simples, 4 tornillos para los hornos dobles/ combos)	50
1. Sosteniendo la puerta firmemente en ambos manos.	50
2. Sostenga la puerta a un ángulo de 30º de la posición cerrada e inserte las bisagras en las ranuras. Tal vez debe mover la puerta ligeramente hacia adelante y atrás para asentar la pata de la bisagra.	50
3. Tal vez es necesario volver a quitar e instalar la puerta hasta que las bisagras estén bien sentadas en las ranuras.	50
4. Abra la puerta completa-mente para exponer las bisagras, palancas y ranuras.	50
5. Empuje las palancas hacia adelante y abajo hasta asentarse en el soporte.	50
6. Cierre y abra la puerta lentamente para asegurarse que se instaló correctamente. La puerta debe estar recta, no chueca.	50
Probar el equipo	50
1. Prenda la corriente en el interruptor.	50
2. Verifique el modo del horno.	50
3. Verifique el que se prendan las luces del horno y que comience a calentarse.	50
4. Compruebe el bloqueo de la puerta.	50
5. Cuando instala un doble horno, aplique la misma prueba también al otro horno.	50
6. Si alguna de las pruebas no resulta como se describe arriba, contacte al servicio de Thermador para recibir ayuda. De otro modo la instalación ya terminó en este momento.	50
Servicio	51
Antes de llamar al servicio	51

Match case Limit results 1 per page

English 1

Safety

WARNING:

If the information in this manual is not followed exactly, fire

or shock may result causing property damage or personal

injury.

WARNING:

Do not repair or replace any part of the appliance unless

specifically recommended in the manuals. Improper

installation, service or maintenance can cause injury or

property damage. Refer to this manual for guidance. All

other servicing should be done by a qualified technician.

Appliance Handling Safety

Do not lift appliance by door handle. Remove the door for

easier handling and installation. See instructions in Use

and Care Manual.

Unit is heavy and requires at least two people or proper

equipment to move.

Hidden surfaces may have sharp edges. Use caution when

reaching behind or under appliance.

Safety Codes and Standards

This appliance complies with one or more of the following

Standards:

•

UL 858, The Standard for the Safety of Household

Electric Ranges

•

UL 923, The Standard for the Safety of Microwave

Cooking Appliances

•

UL 507, The Standard for the Safety of Electric Fans

•

ANSI Z21.1, The American National Standard for

Household Cooking Gas Appliances

•

CAN/CSA-C22.2 No. 113-M1984 Fans and Ventilators

•

CAN/CSA-C22.2 No. 61-M89 Household Cooking

Ranges

It is the responsibility of the owner and the installer to

determine if additional requirements and/or standards

apply to specific installations.

Electric Safety

Before you plug in an electrical cord, be sure all controls

are in the OFF position.

If required by the National Electrical Code (or Canadian

Electrical Code), this appliance must be installed on a

separate branch circuit.

Installer

- show the owner the location of the circuit

breaker or fuse. Mark it for easy reference.

Important

- Save these instructions for the local electrical

inspector's use.

Before installing, turn power OFF at the service panel. Lock

service panel to prevent power from being turned ON

accidentally.

Refer to data plate for more information. See "Data Plate"

under "Service" for data plate location.

Be sure your appliance is properly installed and grounded

by a qualified technician. Installation, electrical connections

and grounding must comply with all applicable codes.

Related Equipment Safety

Remove all tape and packaging before using the appliance.

Destroy the packaging after unpacking the appliance.

Never allow children to play with packaging material.

Never modify or alter the construction of the appliance. For

example, do not remove leveling legs, panels, wire covers

or anti-tip brackets/screws.

Important Safety

Instructions

READ AND SAVE THESE

INSTRUCTIONS