Thermador T18ID905RP Instructions for Use - Page 9

Before using for the first time, Water connection, Electrical connection

Get Thermador T18ID905RP PDF manuals and user guides View all Thermador T18ID905RP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

Before using for the first time 1. Remove information material, adhesive tape and protective foil. 2. Clean the appliance. ~ "Cleaning" on page 24 Water connection 9 CAUTION ■ Installation and connection of the appliance must be carried out by authorized technicians according to the installation instructions supplied. ■ To avoid damage to the appliance and to ensure its proper functioning, it should only be connected to a drinking water system. ■ To avoid water damage, a shut-off valve must be installed. Water pressure of drinking water system 9 CAUTION To avoid damage to the appliance, a pressure relief valve must be installed between the drinking water connection and the tubing, should the water pressure exceed the maximum value. Note: If the water pressure is too low, this will impair the relevant functions of the appliance. ■ Min. 0.2 Mpa (2 bar / 29 psi) ■ Max. 0.8 Mpa (8 bar / 116 psi) Installation and connection en-us Electrical connection 9 CAUTION Do not connect the appliance to electronic energy saver plugs. Note: You can connect the appliance to mainscontrolled and sine-controlled inverters. Mains-controlled inverters are used for photovoltaic systems which are connected directly to the national grid. Sine-controlled inverters must be used for isolated applications. Isolated applications, e.g. on ships or in mountain lodges, are not directly connected to the national grid. 1. After installing the appliance, wait at least 1 hour before connecting it to prevent damaging the compressor. 2. Check that the outlet was installed according to the regulations and complies with the requirements. Requirements for outlets Outlet with Protective conductor Fuse 110 V ... 120 V 60 Hz 10 A ... 16 A Maximum simultaneous load Appliance 6 A 3. Connect the appliance to an outlet near the appliance. The outlet must also be freely accessible following installation of the appliance. If free access is impossible, an all-pole isolating switch must be integrated into the permanent electrical installation according to the installation regulations. 9 WARNING RISK OF ELECTRIC SHOCK! Never use multiple outlets, extension cords or adapters. The appliance must be grounded correctly. Never cut through or remove the power cord's third conductor (grounding conductor). 9 WARNING RISK OF ELECTRIC SHOCK! If the power cord is too short, never use multiple outlets or extension cords. Instead, please contact customer service. 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
Installation and connection
en-us
9
Before using for the first time
1.
Remove information material, adhesive tape and
protective foil.
2.
Clean the appliance.
~
"Cleaning" on page 24
Water connection
9
CAUTION
■
Installation and connection of the appliance
must be carried out by authorized technicians
according to the installation instructions
supplied.
■
To avoid damage to the appliance and to
ensure its proper functioning, it should only be
connected to a drinking water system.
■
To avoid water damage, a shut-off valve must
be installed.
Water pressure of drinking water system
9
CAUTION
To avoid damage to the appliance, a pressure
relief valve must be installed between the
drinking water connection and the tubing,
should the water pressure exceed the
maximum value.
Note:
If the water pressure is too low, this will impair
the relevant functions of the appliance.
■
Min. 0.2 Mpa (2 bar / 29 psi)
■
Max. 0.8 Mpa (8 bar / 116 psi)
Electrical connection
9
CAUTION
Do not connect the appliance to electronic
energy saver plugs.
Note:
You can connect the appliance to mains-
controlled and sine-controlled inverters.
Mains-controlled inverters are used for photovoltaic
systems which are connected directly to the national
grid. Sine-controlled inverters must be used for
isolated applications. Isolated applications, e.g. on
ships or in mountain lodges, are not directly
connected to the national grid.
1.
After installing the appliance, wait at least 1 hour
before connecting it to prevent damaging the
compressor.
2.
Check that the outlet was installed according to
the regulations and complies with the
requirements.
Requirements for outlets
Maximum simultaneous load
3.
Connect the appliance to an outlet near the
appliance.
The outlet must also be freely accessible
following installation of the appliance.
If free access is impossible, an all-pole isolating
switch must be integrated into the permanent
electrical installation according to the installation
regulations.
9
WARNING
RISK OF ELECTRIC SHOCK!
Never use multiple outlets, extension cords
or adapters.
The appliance must be grounded correctly.
Never cut through or remove the power
cord's third conductor (grounding
conductor).
9
WARNING
RISK OF ELECTRIC SHOCK!
If the power cord is too short, never use
multiple outlets or extension cords. Instead,
please contact customer service.
Outlet with
110 V ... 120 V
Protective conductor
60 Hz
Fuse
10 A ... 16 A
Appliance
6 A