Toshiba 62HM95 Owner's Manual - English - Page 104

Lamp unit replacement and care

Get Toshiba 62HM95 - 62inch Rear Projection TV PDF manuals and user guides
UPC - 022265251164
View all Toshiba 62HM95 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 104 highlights

Chapter 11: Appendix Lamp unit replacement and care (continued) How to replace the lamp unit WARNING: RISK OF ELECTRIC SHOCK! TO REDUCE THE RISK OF ELECTRIC SHOCK, NEVER REMOVE TV COVERS, EXCEPT AS SPECIFIED HEREIN. REFER ALL SERVICING NOT SPECIFIED IN THIS MANUAL TO QUALIFIED SERVICE PERSONNEL. Failure to follow this WARNING may result in death or serious injury. Required tools: • Manual Phillips screwdriver • Soft, lint-free gloves. Optional tool: 5/32" or 4mm Allen wrench. 1. Turn off the TV and unplug the power cord. WARNING: Eye damage may result from directly viewing the light produced by this lamp. Always turn off the TV and unplug the power cord before opening the lamp unit door. 4. Using a manual Phillips screwdriver, loosen the two screws on the lamp unit. Lamp unit screws WARNING: RISK OF ELECTRIC SHOCK! The lamp unit door is provided with an interlock to reduce the risk of electric shock and excessive ultraviolet radiation. Never defeat its purpose or attempt to service without removing the lamp unit door completely. Failure to follow this WARNING may result in death or serious injury. 2. STOP! Allow the lamp to cool for at least one (1) hour before replacing it. CAUTION: HOT SURFACE! The temperature of the lamp immediately after use exceeds 392°F (200°C). Touching the lamp before it has cooled will result in severe burns. ALLOW THE LAMP TO COOL FOR AT LEAST ONE (1) HOUR BEFORE REPLACING IT. 5. Grasp the lamp unit handle and gently pull the lamp unit straight out of the TV. Set the old lamp unit aside (see "Disposing of the used lamp unit" on page 105). 3. On the lamp unit door on the side of the TV, loosen the thumb screw by hand or by using a 5/32" or 4mm Allen wrench, and then remove the lamp unit door. TV back Note: Wear soft, lint-free gloves when replacing the lamp unit. Lamp unit door detail Thumb screw 104 HM95_R2_103-109_061505 104 Copyright © 2005 TOSHIBA CORPORATION. All rights reserved. 6/27/05, 6:40 PM

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
(E) 46/52/62HM95
Copyright © 2005 TOSHIBA CORPORATION. All rights reserved.
104
Chapter 11: Appendix
How to replace the lamp unit
WARNING:
RISK OF
ELECTRIC SHOCK!
The lamp unit door is provided with an
interlock to reduce the risk of electric shock and excessive
ultraviolet radiation.
Never defeat its purpose or attempt
to service without removing the lamp unit door
completely.
Failure to follow this WARNING may result in
death or serious injury.
4
.
Using a manual Phillips screwdriver, loosen the two screws on
the lamp unit.
Lamp unit replacement and care
(continued)
Lamp unit screws
3
.
On the lamp unit door on the side of the TV, loosen the
thumb screw by hand or by using a 5/32” or 4mm Allen
wrench, and then remove the lamp unit door.
TV back
Thumb
screw
Lamp unit door detail
CAUTION: HOT SURFACE!
The temperature of the lamp
immediately after use
exceeds 392°F (200°C).
Touching the lamp before it has cooled will result in
severe burns. ALLOW THE LAMP TO COOL FOR AT
LEAST ONE (1) HOUR BEFORE REPLACING IT.
2
.
STOP!
Allow the lamp to cool for at least one (1) hour
before replacing it.
Required tools:
• Manual Phillips screwdriver
• Soft, lint-free gloves.
Optional tool:
5/32” or 4mm Allen wrench.
1
.
Turn off the TV and unplug the power cord.
WARNING: RISK OF
ELECTRIC SHOCK!
TO REDUCE THE RISK OF ELECTRIC SHOCK,
NEVER
REMOVE TV COVERS, EXCEPT AS SPECIFIED
HEREIN.
REFER ALL SERVICING NOT SPECIFIED IN
THIS MANUAL TO QUALIFIED SERVICE PERSONNEL.
Failure to follow this WARNING may result in death
or serious injury.
WARNING:
Eye damage may result from
directly viewing the light produced by this
lamp.
Always turn off the TV and unplug the
power cord before opening the lamp unit door.
5
.
Grasp the lamp unit handle and gently pull the lamp unit
straight out of the TV. Set the old lamp unit aside (see
“Disposing of the used lamp unit” on page 105).
Note: Wear soft, lint-free
gloves when replacing
the lamp unit.
HM95_R2_103-109_061505
6/27/05, 6:40 PM
104