Toshiba DP30A Instruction Manual - Page 20

Set SCAN LIMIT STOPS to ON and exit menu.

Get Toshiba DP30A - Day/Night PTZ Dome Camera CCTV PDF manuals and user guides
UPC - 032017546370
View all Toshiba DP30A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

To enable SCAN LIMIT STOPS: 1. Enter the preset command to access the main menu. Refer to section 6.1 for the controller model and preset command. 2. Position the cursor ( ) next to PAN/TILT SETUP and press the OPEN button to access the Pan/ Tilt menu. 3. Position the cursor next to SCAN LIMIT STOPS and press the OPEN button to move the cursor to the right. 4. Move the joystick up or down to select ON or OFF. 5. To accept the selection, press the OPEN button or to cancel the selection, press the CLOSE button. To set SCAN LIMIT STOPS: 1. Set SCAN LIMIT STOPS to ON and exit menu. 2. Position the camera for the LEFT LIMIT STOP. 3. Enter 92 preset. SCAN LEFT LIMIT will be displayed on screen. 4. Position the camera for the RIGHT LIMIT STOP. If the right limit stop is less than 10 degrees from the left limit stop, NOT ACCEPT will be displayed on screen, 5. Enter 93 preset. SCAN RIGHT LIMIT will be displayed on screen. 6.8.4 MANUAL LIMIT STOPS When a Manual Limit Stop is reached during a manual (joystick) pan, the camera will stop. A Left Manual Limit Stop and Right Manual Limit Stop can be set. The limit stops must be greater than 10 degrees apart. Menu MAIN MENU EXIT PAN/TILT MENU AUTO FLIP ON PROPORTIONALP/T ON SCAN LIMIT STOPS OFF MANUAL LIMIT STOPS OFF PARK TIME MIN 0MIN AUTO PATROL P1ˠOFF SCAN SPEED 5DEG./S SCAN TILT ANGLE 30DEG. STOP TIME 10SEC MAX SPEED 400DEG/S To enable MANUAL LIMIT STOPS: 1. Enter the preset command to access the main menu. Refer to section 6.1 for the controller model and preset command. 2. Position the cursor ( ) next to PAN/TILT SETUP and press the OPEN button to access the Pan/ Tilt menu. 3. Position the cursor next to MANUAL LIMIT STOPS and press the OPEN button to move the cursor to the right. 4. Move the joystick up or down to select ON or OFF. 5. To accept the selection, press the OPEN button or to cancel the selection, press the CLOSE button. To set MANUAL LIMIT STOPS: 1. Set MANUAL LIMIT STOPS to ON and exit menu. 2. Position the camera for the LEFT LIMIT STOP. 3. Enter 90 preset. MANUAL LEFT LIMIT will be displayed on screen. - 20 - Downloaded from www.Manualslib.com manuals search engine

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
- 20 -
To enable SCAN LIMIT STOPS:
1.
Enter the preset command to access the main menu.
Refer to section 6.1 for the controller model and preset command.
2.
Position the cursor (
) next to PAN/TILT SETUP and press the OPEN button to access the Pan/
Tilt menu.
3.
Position the cursor next to SCAN LIMIT STOPS and press the OPEN button to move the cursor
to the right.
4.
Move the joystick up or down to select ON or OFF.
5. To accept the selection, press the OPEN button or to cancel the selection, press the CLOSE
button.
To set SCAN LIMIT STOPS:
1.
Set SCAN LIMIT STOPS to ON and exit menu.
2.
Position the camera for the LEFT LIMIT STOP.
3.
Enter 92 preset. SCAN LEFT LIMIT will be displayed on screen.
4.Position the camera for the RIGHT LIMIT STOP. If the right limit stop is less than 10 degrees
from the left limit stop, NOT ACCEPT will be displayed on screen,
5.
Enter 93 preset. SCAN RIGHT LIMIT will be displayed on screen.
6.8.4
MANUAL LIMIT STOPS
When a Manual Limit Stop is reached during a manual (joystick) pan, the camera will stop. A Left
Manual Limit Stop and Right Manual Limit Stop can be set. The limit stops must be greater than 10
degrees apart.
Menu
<CAMERA SETUP>
<PAN/TILT SETUP>
<PRESET TITLES>
<OTHERS>
EXIT
MAIN MENU
PAN/TILT MENU
AUTO FLIP
ON
PROPORTIONALP/T
ON
SCAN LIMIT STOPS
OFF
MANUAL LIMIT STOPS
OFF
PARK TIME MIN
0MIN
AUTO PATROL P1
→
OFF
SCAN SPEED
5DEG./S
SCAN TILT ANGLE
30DEG.
STOP TIME
10SEC
MAX SPEED
400DEG/S
To enable MANUAL LIMIT STOPS:
1.
Enter the preset command to access the main menu.
Refer to section 6.1 for the controller model and preset command.
2.
Position the cursor (
) next to PAN/TILT SETUP and press the OPEN button to access the Pan/
Tilt menu.
3. Position the cursor next to MANUAL LIMIT STOPS and press the OPEN button to move the
cursor to the right.
4.
Move the joystick up or down to select ON or OFF.
5. To accept the selection, press the OPEN button or to cancel the selection, press the CLOSE
button.
To set MANUAL LIMIT STOPS:
1.
Set MANUAL LIMIT STOPS to ON and exit menu.
2.
Position the camera for the LEFT LIMIT STOP.
3.
Enter 90 preset. MANUAL LEFT LIMIT will be displayed on screen.
Downloaded from
www.Manualslib.com
manuals search engine