Toshiba Satellite Pro U300 Maintenance Manual - Page 229

Installing the LCD unit/FL Inverter, screws, LCD unit, LCD harness, conductive tape, display mask

Get Toshiba Satellite Pro U300 PDF manuals and user guides View all Toshiba Satellite Pro U300 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 229 highlights

Replacement Procedures Installing the LCD unit/FL Inverter The following describes the procedure for installing the LCD unit and FL inverter (See Figure 4-31 to 4-34). 1. Install the LCD supports (LCD unit side) to the LCD and secure them with the following screws. • M2.0×2.5 BINK screw x4 2. Stand the LCD unit on the display cover and connect the LCD harness to the connector on the back of LCD. 3. Stick the conductive tape on the connector of LCD harness. 4. Secure the LCD unit with the following screws. • M2.5×4.0 BINK screw x2 5. Connect LCD harnesses to the connector CN1 of the FL inverter. CAUTION: Be careful not to connect the LCD harnesses to the wrong connectors of FL inverter. 6. Connect HV harnesses to the connector CN2 of the FL inverter. 7. Install the display mask while fitting the latches. 8. Secure the display mask with following screws M2.5×5.0 BIND screw X6 9. Cover screws with Screw rubber cover X6 NOTE: When installing the display mask, make sure there is no gap between the display mask and the display cover. 54Satellite U300 and Satellite Pro U300 Maintenance Manual (960-Q08)

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
Replacement Procedures
54Satellite U300 and Satellite Pro U300
Maintenance Manual (960-Q08)
Installing the LCD unit/FL Inverter
The following describes the procedure for installing the LCD unit and FL inverter (See
Figure 4-31 to 4-34).
1.
Install the LCD supports (LCD unit side) to the LCD and secure them with the
following
screws
.
•
M2.0
×
2.5 BINK
screw
x4
2.
Stand the
LCD unit
on the display cover and connect the
LCD harness
to the
connector on the back of LCD.
3.
Stick the
conductive tape
on the connector of LCD harness.
4.
Secure the LCD unit with the following
screws
.
•
M2.5
×
4.0 BINK screw
x2
5.
Connect
LCD harnesses
to the connector
CN1
of the FL inverter.
CAUTION:
Be careful not to connect the LCD harnesses to the wrong connectors of FL
inverter.
6.
Connect
HV harnesses
to the connector
CN2
of the FL inverter.
7.
Install the
display mask
while fitting the latches.
8.
Secure the display mask with following
screws
M2.5
×
5.0
BIND screw
X6
9.
Cover screws with
Screw rubber cover
X6
NOTE:
When installing the display mask, make sure there is no gap between the display
mask and the display cover.