Troy-Bilt CSV 070 Service Manual

Troy-Bilt CSV 070 Manual

Get Troy-Bilt CSV 070 PDF manuals and user guides View all Troy-Bilt CSV 070 manuals
Add to My Manuals
Save this manual to your list of manuals

Troy-Bilt CSV 070 manual content summary:

  • Troy-Bilt CSV 070 | Service Manual - Page 1
    Service Manual SELF PROPELLED CHIPPER VAC - CSV 070 NOTE: These materials are for use by trained technicians experienced in the service and repair of Instructions, photographs and illustrations used in this publication are for reference use only and may not depict actual model and component parts.
  • Troy-Bilt CSV 070 | Service Manual - Page 2
  • Troy-Bilt CSV 070 | Service Manual - Page 3
    TABLE OF CONTENTS Safety Switch ...1 Inspection of the Drive System 3 Transmission Removal ...5 Impeller and Belt Removal ...8 Chipper Blade Removal ...11 0
  • Troy-Bilt CSV 070 | Service Manual - Page 4
  • Troy-Bilt CSV 070 | Service Manual - Page 5
    Self-propelled Chipper Shredder Vacuum Self-propelled Chipper Shredder Vacuum ABOUT THIS SECTION: In model year 2000, MTD introduced a vertical crankshaft lawn vacuum with a 22" In figure 1.3, the meter shows continuity (near 0 ohms). This engine will not start even though the bag is in place. 1
  • Troy-Bilt CSV 070 | Service Manual - Page 6
    Self-propelled Chipper Shredder Vacuum 1.4. If bad connection exists between the switch and ground. NOTE: A lock tab secures the plug to the switch. The switch must be removed to reach the lock tab. 1.9. engine without a blower chute or collector bag in place. This is unsafe. 1.7. 2 Figure 1.10
  • Troy-Bilt CSV 070 | Service Manual - Page 7
    propelled Chipper Shredder Vacuum 1.11 the magneto, the problem lies in the wiring or the ground connection. 1.13. Do not return a machine to service unless this safety with the engine running or by pulling the engine through manually. • The belt and pulley system operates whenever the engine is
  • Troy-Bilt CSV 070 | Service Manual - Page 8
    Self-propelled Chipper Shredder Vacuum 2.4. Watch the travel of the variable speed sheave (pulley) on shaft, but fails to drive the wheels when the self propel bail is lifted, then there may be a problem in one of three areas: • The cable that connects the bail to the clutch mechanism. • The final
  • Troy-Bilt CSV 070 | Service Manual - Page 9
    Self-propelled Chipper Shredder Vacuum 2.11. Confirm that the drive gears are installed on the correct side. See Figure 2.11. 3. TRANSMISSION REMOVAL 3.1. Disconnect the H.T. lead from the spark plug. 3.2. Remove collection bag or blower chute. 3.3. Remove vacuum hose if attached. 3.4. Using a
  • Troy-Bilt CSV 070 | Service Manual - Page 10
    Self-propelled Chipper Shredder Vacuum 3.7. Safely support rear of the unit so that the rear wheels are off the ground, and remove rear hub caps. See Figure 3.7. 3.10. Remove retaining ring holding drive gear and dowel pin on axle. See Figure 3.10. Dust cover 4X4 supports Figure 3.7 3.8. Using a
  • Troy-Bilt CSV 070 | Service Manual - Page 11
    Self-propelled Chipper Shredder Vacuum 3.13. Remove three self tapping screws holding transmission brace to the frame using an 3/8 socket. 3.14. Remove the two phillips screws holding the transmission to
  • Troy-Bilt CSV 070 | Service Manual - Page 12
    Self-propelled Chipper Shredder Vacuum 3.19. Pivot transmission rearward while sliding it to the right Disconnect the H.T. lead from the spark plug. 4.2. Remove the transmission as described in the TRASMISSION REMOVAL section of this manual. 4.3. Safely tilt and support the front of unit to provide
  • Troy-Bilt CSV 070 | Service Manual - Page 13
    Self-propelled Chipper Shredder Vacuum 4.7. Use a 1/4" wrench to remove the three Screws securing the black plastic nozzle to the lower housing. They are accessible from underneath. See Figure 4.7. 4.9. Tilt top of black plastic nozzle toward the engine to remove. This will allow the safety gate
  • Troy-Bilt CSV 070 | Service Manual - Page 14
    Self-propelled Chipper Shredder Vacuum 4.11. Block the impeller with a chock, to keep it from rotating. Using a 9/16" socket, remove the bolt, lock washer, and flat washer securing the impel- ler to the crankshaft. See Figure 4.11. Bolt Impeller 4.15. In servicing the impeller: • The pulley
  • Troy-Bilt CSV 070 | Service Manual - Page 15
    REMOVAL 5.1. Disconnect H.T. lead from the spark plug. 5.2. Remove the three bolts holding the chipper chute to the upper housing. See Figure 5.2. Self-propelled Chipper Shredder Vacuum 5.4. Using 3/16" allen wrench, remove the flat head cap screw that holds the chipper blade to the impeller. It is
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
Service Manual
MTD Products LLC - Product Training and Education Department
FORM NUMBER 769-01422
5/2004
SELF PROPELLED CHIPPER VAC - CSV 070