Vtech LS6126-5 User Manual - Page 40

Set remote access code, Set message alert tone

Get Vtech LS6126-5 PDF manuals and user guides View all Vtech LS6126-5 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

Basic oApenrsawtioenring system Answering system Set remote access code A two-digit security code is required to access the answering system remotely from any touch tone telephone. The preset code is 19. You can set the code from 10 to 99. To set the remote access code: 1. Press SET UP when the phone is not in use, until the system announces the remote access code setting. 2. Press /SKIP or /REPEAT to change the remote access code by one, or press and hold /SKIP or /REPEAT to change it by increments of ten. P��r�e�s�s� SET UP to save the setting and go to the next setting, or press /PLAY/STOP to save and exit set up mode. Set message alert tone This feature programs the system to beep every 10 seconds to alert you of new messages. The tone will stop when all new messages have been reviewed. To set the message alert tone: 1. Press SET UP when in idle mode until the system announces the message alert tone setting. 2. Press /SKIP or /REPEAT to select on or off, then press SET UP to save the setting and go to the next setting, or press /PLAY/STOP to save and exit set up mode. • The answering system must be turned on for the message alert tone to function. www.vtechphones.com 37

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
www.vtechphones.com
37
Basic operation
Answering system
Answering system
Set remote access code
A two-d±g±t secur±ty code ±s requ±red to access the answer±ng system remotely
from any touch tone telephone. The preset code ±s
19
. You can set the code
from
10
to
99
.
To set the remote access code:
Press
SET UP
when the phone ±s not ±n use, unt±l the system announces the
remote access code sett±ng.
Press
/
SKIP
or
/
REPEAT
to change the remote access code by one, or
press and hold
/
SKIP
or
/
REPEAT
to change ±t by ±ncrements of ten.
Press
Press
SET UP
to save the sett±ng and go to the next sett±ng, or press
/
PLAY/STOP
to save and ex±t set up mode.
Set message alert tone
Th±s feature programs the system to beep every 10 seconds to alert you of new
messages. The tone w±ll stop when all new messages have been rev±ewed.
To set the message alert tone:
Press
SET UP
when ±n ±dle mode unt±l the system announces the message
alert tone sett±ng.
Press
/SKIP
or
/REPEAT
to select on or off, then press
SET UP
to save
the sett±ng and go to the next sett±ng, or press
/PLAY/STOP
to save and
ex±t set up mode.
1.
2.
1.
2.
The answer±ng
system must be
turned on for the
message alert
tone to funct±on.
•