Weber Summit FT 600 LP Owners Manual - Page 39

Main Burner Flame Pattern, Main Burner Cleaning Procedure, Replacing the Burners

Get Weber Summit FT 600 LP PDF manuals and user guides View all Weber Summit FT 600 LP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

Main Burner Flame Pattern The Weber Gas Barbecue burners have been factory set for the correct air and gas mixture. The correct flame pattern is shown in Figure 13. Burner inside cooking box Tips occasionally yellowish Light blue Flames Figure 13 Dark blue If the flames do not appear to be uniform the length of the burner tube, follow the burner cleaning procedures. Main Burner Cleaning Procedure Turn off the gas supply. Remove the manifold. (See Section "Replacing the main burners".) Look inside each burner with a flashlight. Figure 14. Replacing the Burners 1. Your Weber Gas Barbecue must be OFF and cool. 2. Turn OFF gas at source. 3. Disconnect regulator. 4. To remove control panel refer to Step "Remove the control panel and the front panel". 5. Remove splash guards. 6. Remove cooking grill(s) and griddle. 7. Remove Flavorizer bars. 8. Remove the manifold by unsnapping the clips at the right and left front of the cooking box. Figure 16. Figure 14 Clean the inside of the burners with a wire (a straightened out coat hanger will work). Figure 15. Check and clean the air shutter opening at the ends of the burners. Check and clean the valve orifices at the base of the valves. Use a brass bristle brush to clean outside of burners. This is to make sure all the burner ports are fully open. Figure 16 9. Disconnect white and black wire from each igniter. Figure 17. Figure 15 ƽCAUTION: Do not enlarge the burner ports when cleaning. White wire Black wire Figure 17 39

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
Main Burner Flame Pattern
The Weber Gas Barbecue burners have been factory set
for the correct air and gas mixture. The correct flame
pattern is shown in Figure 13.
If the flames do not appear to be uniform the length of the
burner tube, follow the burner cleaning procedures.
Main Burner Cleaning Procedure
Turn off the gas supply.
Remove the manifold.
(See Section “Replacing the main burners”.)
Look inside each burner with a flashlight. Figure 14.
Clean the inside of the burners with a wire
(a straightened out coat hanger will work). Figure 15.
Check and clean the air shutter opening at the ends of
the burners. Check and clean the valve orifices at the
base of the valves. Use a brass bristle brush to clean
outside of burners. This is to make sure all the burner
ports are fully open.
m
CAUTION:
Do not enlarge the burner ports when
cleaning.
39
Replacing the Burners
1.
Your Weber Gas Barbecue must be OFF and cool.
2.
Turn OFF gas at source.
3.
Disconnect regulator.
4.
To remove control panel refer to Step “Remove the
control panel and the front panel”.
5.
Remove splash guards.
6.
Remove cooking grill(s) and griddle.
7.
Remove Flavorizer bars.
8.
Remove the manifold by unsnapping the clips at the
right and left front of the cooking box. Figure 16.
9.
Disconnect white and black wire from each igniter.
Figure 17.
Figure 16
Figure 17
Black wire
White wire
Figure 13
Burner inside
cooking box
Flames
Tips occasionally yellowish
Light blue
Dark blue
Figure 14
Figure 15