Weber Summit FT 600 LP Owners Manual - Page 41

Crossover Ignition System Operations, tightly, contact Weber-Stephen Customer Service.

Get Weber Summit FT 600 LP PDF manuals and user guides View all Weber Summit FT 600 LP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

13. Lift and twist the burner assembly slightly to separate the crossover tube from the burners. Remove the burners from the cooking box. Figure 21. Separate here Crossover tube 15. Reinstall the Spider Stopper Guards. Slightly rotate the Spider Stopper Guards so that the seams are in line with the Venturi fins. There should be no gaps in the seams or in the fit around the burners and valves. Figure 23. Venturi fin Check fit around valve Figure 21 14. To reinstall the burners, reverse steps 3 through 13. ƽCAUTION: The burner openings must be positioned properly over the valve orifices. Figure 22a. Check proper assembly before fastening manifold in place. Figure 22b. (a) Valve Burner (b) Check fit around burner Figure 23 ƽCAUTION: If the Spider Stopper Guards do not fit tightly, contact Weber-Stephen Customer Service. ƽCAUTION: After reinstalling the gas lines, they should be leak checked with a soap and water solution before using the barbecue. See Step"Check for gas leaks". Crossover Ignition System Operations If the Crossover Ignition System fails to ignite the Front burner, light the Front burner with a match. If the Front burner lights with a match, then check the Crossover Ignition System. s Check that both the white and black ignition wires are attached properly. Figure 24. Figure 22 Figure 24 s Check that the Crossover Ignition button pushes the igniter (button) down, and returns to the up position. s Check to see if the igniter is loose in the frame. Tighten if necessary; see Step "Install igniter" for correct procedure. If the Crossover Ignition System still fails to light, contact your dealer. 41

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
41
Crossover Ignition System Operations
If the Crossover Ignition System fails to ignite the Front
burner, light the Front burner with a match. If the Front
burner lights with a match, then check the Crossover
Ignition System.
■
Check that both the white and black ignition wires
are attached properly. Figure 24.
■
Check that the Crossover Ignition button pushes the
igniter (button) down, and returns to the up position.
■
Check to see if the igniter is loose in the frame.
Tighten if necessary; see Step “Install igniter” for
correct procedure.
If the Crossover Ignition System still fails to light, contact
your dealer.
Figure 24
15.
Reinstall the Spider Stopper Guards. Slightly rotate
the Spider Stopper Guards so that the seams are in
line with the Venturi fins. There should be no gaps
in the seams or in the fit around the burners and
valves. Figure 23.
m
CAUTION:
If the Spider Stopper Guards do not fit
tightly, contact Weber-Stephen Customer Service.
m
CAUTION:
After reinstalling the gas lines, they
should be leak checked with a soap and water
solution before using the barbecue. See Step“Check
for gas leaks”.
Venturi fin
Figure 23
Check fit
around valve
Check fit around burner
13.
Lift and twist the burner assembly slightly to
separate the crossover tube from the burners.
Remove the burners from the cooking box.
Figure 21.
Figure 21
Separate here
Crossover tube
14.
To reinstall the burners, reverse steps 3 through 13.
m
CAUTION:
The burner openings must be
positioned properly over the valve orifices.
Figure 22a.
Check proper assembly before fastening manifold in
place. Figure 22b.
Figure 22
(a)
(b)
Valve
Burner