Weider 3550 User Manual - Page 13

Route the Lat Cable 88 over a 3 1/2 Pulley 78.

Get Weider 3550 PDF manuals and user guides View all Weider 3550 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

24. Route the Lat Cable (88) over a 3 1/2" Pulley (78). 24 Slide a Long Cable Trap (102) onto a 3/8" x 1 3/4" Bolt (93). Attach the Pulley to the indicated bracket on the Top Frame (6) with the Bolt and a 3/8" Nylon Locknut (87). Make sure that the Long Cable Trap is turned to hold the Cable in the groove of the Pulley. 6 87 78 88 102 93 25. Remove the preassembled 3/8" Nylon Locknut (87) 25 and 3/8" x 2" Bolt (100) from the Pulley Plates (63). Wrap the Lat Cable (88) under a 3 1/2" Pulley (78). Attach the Pulley and a Cable Trap (68) between the indicated holes in the Pulley Plates (63) with the 3/8" x 2" Bolt (100) and the 3/8" Nylon Locknut (87). Make sure that the Cable Trap is turned to hold the Cable in place. 26. Attach the end of the Lat Cable (88) inside of the 26 Butterfly Top Frame (7) with a 5/16" x 2 1/2" Bolt (59), two 5/16" Washers (90), and a 5/16" Nylon Locknut (86). 100 88 78 87 68 63 63 86 90 90 7 59 88 27. Locate the Butterfly Cable (69), which is the 27 shortest Cable. Attach the Cable to the Pivot Bracket (70) on the Left Butterfly Arm (25) with a 5/16" x 1" Shoulder Bolt (103) and a 5/16" Nylon Locknut (86). 13 86 69 103 70 25

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
13
24. Route the Lat Cable (88) over a 3 1/2” Pulley (78).
Slide a Long Cable Trap (102) onto a 3/8” x 1 3/4”
Bolt (93). Attach the Pulley to the indicated bracket
on the Top Frame (6) with the Bolt and a 3/8” Nylon
Locknut (87).
Make sure that the Long Cable
Trap is turned to hold the Cable in the groove of
the Pulley.
25. Remove the preassembled 3/8” Nylon Locknut (87)
and 3/8” x 2” Bolt (100) from the Pulley Plates (63).
Wrap the Lat Cable (88) under a 3 1/2” Pulley (78).
Attach the Pulley and a Cable Trap (68) between
the indicated holes in the Pulley Plates (63) with the
3/8” x 2” Bolt (100) and the 3/8” Nylon Locknut (87).
Make sure that the Cable Trap is turned to hold
the Cable in place.
26. Attach the end of the Lat Cable (88) inside of the
Butterfly Top Frame (7) with a 5/16” x 2 1/2” Bolt
(59), two 5/16” Washers (90), and a 5/16” Nylon
Locknut (86).
27.
Locate the Butterfly Cable (69), which is the
shortest Cable.
Attach the Cable to the Pivot
Bracket (70) on the Left Butterfly Arm (25) with a
5/16” x 1” Shoulder Bolt (103) and a 5/16” Nylon
Locknut (86).
27
24
25
26
78
88
87
93
6
68
63
87
78
88
88
90
86
90
59
7
86
69
103
70
25
100
63
102