Weider 3550 User Manual - Page 16

Wrap the VKR Low Cable 72 over a 3 1/2 Pulley

Get Weider 3550 PDF manuals and user guides View all Weider 3550 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

36. Remove the preattached 3 1/2" Pulley (not shown) from the "U"-bracket (64). 36 Attach the end of the Leg Lever Cable (75) to the "U"-bracket (64) with a 1/4" Washer (97) and a 1/4" Nylon Locknut (34). Note: Do not completely tighten the Nylon Locknut; it should be threaded only two turns onto the end of the Cable. 75 64 97 34 37. Locate the VKR Low Cable (72), which is the only remaining cable that has an eyelet on one 37 end and a ball on the other end. Route the eyelet end of the Cable through the cage on the Long 78 5 87 Base (120) and through the VKR Upright (5) as 72 shown. Attach a 3 1/2" Pulley (78) to the indicated bracket on the Long Base (120) with 3/8" x 1 3/4" Bolt (93) and a 3/8" Nylon Locknut (87). 93 120 38. Wrap the VKR Low Cable (72) under a 3 1/2" 38 Pulley (78). Attach the Pulley to the indicated brack- et on the Long Base (120) with a 3/8" x 1 3/4" Bolt (93) and a 3/8" Nylon Locknut (87). 39. Wrap the VKR Low Cable (72) over a 3 1/2" Pulley 39 (78). Attach the Pulley to the Offset Double "U"- bracket (61) with a 3/8" x 1 3/4" Bolt (93) and a 3/8" Nylon Locknut (87). 16 87 78 72 93 120 93 87 61 72 78

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
16
36.
Remove the preattached 3 1/2” Pulley (not
shown) from the “U”-bracket (64).
Attach the end of the Leg Lever Cable (75) to the
“U”-bracket (64) with a 1/4” Washer (97) and a 1/4”
Nylon Locknut (34).
Note: Do not completely
tighten the Nylon Locknut; it should be thread-
ed only two turns onto the end of the Cable.
37.
Locate the VKR Low Cable (72), which is the
only remaining cable that has an eyelet on one
end and a ball on the other end.
Route the eyelet
end of the Cable through the cage on the Long
Base (120) and through the VKR Upright (5) as
shown.
Attach a 3 1/2” Pulley (78) to the indicated bracket
on the Long Base (120) with 3/8” x 1 3/4” Bolt (93)
and a 3/8” Nylon Locknut (87).
38. Wrap the VKR Low Cable (72) under a 3 1/2”
Pulley (78). Attach the Pulley to the indicated brack-
et on the Long Base (120) with a 3/8” x 1 3/4” Bolt
(93) and a 3/8” Nylon Locknut (87).
39. Wrap the VKR Low Cable (72) over a 3 1/2” Pulley
(78). Attach the Pulley to the Offset Double “U”-
bracket (61) with a 3/8” x 1 3/4” Bolt (93) and a 3/8”
Nylon Locknut (87).
36
37
38
75
78
72
78
93
93
87
5
87
78
39
97
34
64
120
72
72
61
93
87
120