Weider Cts 2000 Club Series English Manual - Page 6
Entire, Assembly, Shown, Luded
View all Weider Cts 2000 Club Series manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 6 highlights
PAGE 9 WEIDER SPORTING GOODS FORT T DURING THE FOLLOWING ASSEMBLY STEPS, YOU WILL FIND ASSEMBLY .P0IN0RiSrEsTi-RA.SUSCAETTMIOBTNLHSEEDS,H.SFAATDECEPTDSOI:RHNYABVOEFXOOERNSLSYYUOBC.IEHRE,.NACSFOFATNSHVTISEE.NN"EITEDHNEFCSIENE.GA.ESRSSEETMIVGEBHRLTIAE. LSYOHOUAFaVWETILBHLEEBESNEE. INSTRUCTED THE -ENTIRE IN LUDED `IN "TTAHOSASTTEIAGMtH§BETLEMYNEI3TStH: ESHSOEWANSSEAMNDBLIE:SO;DTILTUYERNINNGOUTTHESOSTETPHAINTSTARLULC. PTAIORNTSS.!. STEP 1 FRAME ASSEMBLY PART NAME 50 5/16" FLAT WASHER 51 5/16" NYLON LOCK NUT 53 5/16" X 2 3/4" HEX HEAD BOLT 55 5/16" X 11/2" HEX HEAD BOLT 56 5116" X 23/4" CARRIAGE BOLT 56 5/16" X r HEX HEAD BOLT 77 5/16" X 2112" CARRIAGE BOLT 60 2" SQUARE PLASTIC INSERT CAP 81 r SQUARE RUBBER COVER CAP 63 1 1/4" SQUARE PLASTIC INSERT CAP 97 1" LONG PLASTIC SLEEVE QTY 3 8 2 1 2 1 2 1 2 1 1 Cap the front endofthe BASE FRAME (1) with a 2" SQUARE PLASTIC INSERT CAP (80). nth the BASE FRAME (1) oriented so the welded plate at the front of the Base will be to the ground when assembled, fasten the ARM PRESS UPRIGHT (2) to the front section of the Base with two 5/16" X 2 1/2" CARRIAGE BOLTS (77) and 5/16" NYLON LOCK NUTS (51). Note that the UPRIGHT (2) should tilt back toward the rear of the Base when assembled. Select the 2" SQUARE X 38" LONG REAR BASE TUBE (3). Cap each end of the REAR BASE TUBE (3) with a 2" SQUARE RUBBER COVER CAP (81). Position the REAR BASE TUBE (3) into the "L" bracket of the BASE FRAME (1) so the longest section of the REAR BASE TUBE (3) is to the right (as you face the front of the unit). Bolt up through the Rear Base Tube and Bracket with 5/16" X 2 3/4" CARRIAGE BOLTS (56). Sit the STEPPER UPRIGHT (4) over the Bolts so the Plate at the top of the Upright slants upward from the back to the front. Bolt the BASE FRAME (1) andUPRIGHT (4) securely with 5/16" NYLON LOCK NUTS (51). o Locate the BASE PULLEY BRACKET (7) with the pm-assembledPulley. (This is a flatplate 2"X 6" with two holes at one end and a single hole at the other.) Assemble this Bracket to the LEFT side of the BASE FRAME (1) with two 5/16" X 2 3/4" HEX HEAD BOLTS (53). Secure with 5/16" FLAT WASHERS (50) and 5/16" NYLON LOCK NUTS (51). Cap the end of the Welded Stopper Tube on the ARM PRESS UPRIGHT (2) with a 1 1/4" SQUARE PLASTIC INSERT CAP (83). Remove the STATION 1 DECAL (121) from the backing sheet and position the Decal to the front of the ARM PRESS UPRIGHT (2) below the Welded Stopper Tube.