Weslo Momentum G 3.1 Elliptical English Manual - Page 11

IMPORTANT: If the Console has

Page 11 highlights

11. Apply grease to an M10 x 70mm Bolt (60). Attach the Right Pedal Arm (12) to the right Upper Body Leg (64) with the M10 x 70mm Bolt (60), two M10 Special Washers (80), two M10 Split Washers (78), two M10 Washers (62), two Nylon Washers (73), and an M10 Locknut (53) as shown. Make sure that the Nylon Washers are between the Upper Body Leg and the bracket on the Right Pedal Arm. See the inset drawing. Press a Dome Cap (14) firmly onto each M10 Special Washer (80); the Dome Caps will snap onto the Special Washers. Attach the Left Pedal Arm not shown) to the left Upper Body Leg (64) in the same way. 11 64 14 80 53 80 78 64 73 80 14 62 78 80 12 62 60 Grease 12. The Console (23) can use four AA batteries (not included); alkaline batteries are recommended. 12 Do not use old and new batteries together or alkaline, standard, and rechargeable batter- ies together. IMPORTANT: If the Console has been exposed to cold temperatures, allow it to warm to room temperature before insert- ing batteries. Otherwise, you may damage the console or other electronic components. Remove the battery cover from the back of the Console (23), and insert batteries into the battery compartment. Make sure to orient the batteries as shown by the diagram inside the battery compartment. Then, reattach the battery cover. 13. While a second person holds the Console (23) near the Upright (2), connect the console wire 13 to the Wire Harness (31). Insert the excess wire into the Console (23) or into the Upright (2). Tip: Be careful to avoid pinching the wires. Attach the Console (23) to the Upright (2) with four ST4.2 x 12mm Self-tapping Screws (66). See step 4. Tighten the three M8 x 20mm Button Screws (54) and the three M8 Locknuts (58). 23 Battery Compartment 23 31 2 66 Avoid pinching the wires 14. Make sure that all parts of the elliptical are properly tightened. Note: Extra hardware may be left over after assembly is completed. To protect the floor or carpet from damage, place a mat under the elliptical. 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20

11
13. While a second person holds the Console (23)
near the Upright (2), connect the console wire
to the Wire Harness (31). Insert the excess wire
into the Console (23) or into the Upright (2).
Tip: Be careful to avoid pinching the wires.
Attach the Console (23) to the Upright (2) with
four ST4.2 x 12mm Self-tapping Screws (66).
See step 4.
Tighten the three M8 x 20mm Button
Screws (54) and the three M8 Locknuts (58).
12.
The Console (23) can use four AA batteries (not
included); alkaline batteries are recommended.
Do not use old and new batteries together or
alkaline, standard, and rechargeable batter-
ies together.
IMPORTANT: If the Console has
been exposed to cold temperatures, allow it
to warm to room temperature before insert-
ing batteries. Otherwise, you may damage
the console or other electronic components.
Remove the battery cover from the back of the
Console (23), and insert batteries into the battery
compartment.
Make sure to orient the bat-
teries as shown by the diagram inside the
battery compartment.
Then, reattach the bat-
tery cover.
14.
Make sure that all parts of the elliptical are properly tightened.
Note: Extra hardware may be left over
after assembly is completed. To protect the floor or carpet from damage, place a mat under the elliptical.
13
12
23
Battery
Compartment
66
2
31
Avoid pinching
the wires
11. Apply grease to an M10 x 70mm Bolt (60).
Attach the Right Pedal Arm (12) to the right
Upper Body Leg (64) with the M10 x 70mm Bolt
(60), two M10 Special Washers (80), two M10
Split Washers (78), two M10 Washers (62), two
Nylon Washers (73), and an M10 Locknut (53)
as shown.
Make sure that the Nylon Washers
are between the Upper Body Leg and the
bracket on the Right Pedal Arm.
See the inset drawing.
Press a Dome Cap (14)
firmly onto each M10 Special Washer (80); the
Dome Caps will snap onto the Special Washers.
Attach the Left Pedal Arm not shown) to the
left Upper Body Leg (64) in the same way.
11
14
14
80
80
80
80
64
73
64
53
78
78
62
62
12
60
Grease
23