Whirlpool WDF518SAH Installation Instructions - Page 12

Connect Fill Hose To Elbow

Get Whirlpool WDF518SAH PDF manuals and user guides View all Whirlpool WDF518SAH manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

CONNECT FILL HOSE TO ELBOW 13. Flexible line 15. Install strain relief White Black Flexible braided line: Confirm the flexible braided line is long enough. Attach flexible line to elbow then route hose out the bottom left channel under the dishwasher. Secure in channel with tape or wire ties. POWER CORD CONNECTION WARNING Install a UL Listed/CSA Approved metallic strain relief. Make sure screw heads are facing up when tightening conduit nut. Strain relief is provided with the power cord kit. See the "Tools and Parts" section for part details and ordering information. 16. Power cord-route cord into terminal box Electrical Shock Hazard Electrically ground dishwasher. Connect ground wire to green ground connector in terminal box. Do not use an extension cord. Failure to follow these instructions can result in death, fire, or electrical shock. NOTE: If removing a previous dishwasher with a power cord, you will need to transfer the power cord to the new dishwasher. 14. Remove terminal box cover Select UL Listed/CSA Approved twist-on wire connectors of the proper size. See the "Tools and Parts" section for part details. Connect wires, black-to-black and white-to-white, using the twist-on wire connectors. NOTE: Do not pre-twist stranded wire. Twist on wire connector. Gently tug on wires to be sure both are secured. Route cord so that it does not touch dishwasher motor or lower part of dishwasher tub. Pull cord through strain relief in terminal box. NOTE: A maximum of two power cord supply conductors (12 AWG largest size) plus one grounding conductor are permitted in the terminal box. Remove the ground connector screw on the raised floor inside the box and place it through the ring terminal of the green ground wire of power cord. Reattach and tighten the ground connector screw to the raised floor of the box. Tighten strain relief screws to secure cord. Terminal box cover Wiring configuration Remove the screw holding the terminal box cover. Remove the cover by sliding it up and lifting the hooks out of the slot. Keep the cover for later use. 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
12
CONNECT FILL HOSE TO ELBOW
13.
Flexible line
Flexible braided line:
Confirm the flexible braided line is long
enough.
Attach flexible line to elbow then route hose out the bottom left
channel under the dishwasher. Secure in channel with tape or
wire ties.
POWER CORD CONNECTION
WARNING
Electrical Shock Hazard
Electrically ground dishwasher.
Connect ground wire to green ground connector in
terminal box.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
NOTE:
If removing a previous dishwasher with a power cord,
you will need to transfer the power cord to the new dishwasher.
14.
Remove terminal box cover
Terminal
box cover
Remove the screw holding the terminal box cover. Remove the
cover by sliding it up and lifting the hooks out of the slot. Keep
the cover for later use.
15.
Install strain relief
Install a UL Listed/CSA Approved metallic strain relief. Make
sure screw heads are facing up when tightening conduit nut.
Strain relief is provided with the power cord kit. See the “Tools
and Parts” section for part details and ordering information.
16.
Power cord—route cord into
terminal box
Select UL Listed/CSA Approved twist-on wire connectors of the
proper size. See the “Tools and Parts” section for part details.
Connect wires, black-to-black and white-to-white, using the
twist-on wire connectors.
NOTE:
Do not pre-twist stranded wire. Twist on wire connector.
Gently tug on wires to be sure both are secured.
Route cord so that it does not touch dishwasher motor or lower part
of dishwasher tub. Pull cord through strain relief in terminal box.
NOTE:
A maximum of two power cord supply conductors
(12 AWG largest size) plus one grounding conductor are
permitted in the terminal box.
Remove the ground connector screw on the raised floor inside
the box and place it through the ring terminal of the green ground
wire of power cord. Reattach and tighten the ground connector
screw to the raised floor of the box. Tighten strain relief screws
to secure cord.
Wiring configuration
White
Black