Whirlpool WDF518SAH Installation Instructions - Page 20

Option D: No waste disposer

Get Whirlpool WDF518SAH PDF manuals and user guides View all Whirlpool WDF518SAH manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

Option D: No waste disposer - with air gap Screw-type clamps Waste tee Drain trap Air gap Large drain hose clamp Rubber hose connector Drain hose 1 Rubber end 2 1. Connect rubber end of drain hose to air gap. 2. Attach drain hose to air gap. Use a 1" to 11/2" (2.5 to 3.8 cm) screw-type clamp. 3 3. Use a rubber hose (not provided) with screw-type clamps (not provided) to connect from waste tee to air gap. COMPLETE INSTALLATION Check that the power supply wire or cord does not touch dishwasher motor or the lower part of the dishwasher tub. 48. Power supply cord-Plug into a grounded 3 prong outlet Plug into a grounded 3 prong outlet. 49. Reconnect power Reconnect electrical power at the fuse box or circuit breaker box. NOTE: With the access panel off, start the dishwasher and allow it to complete the shortest wash cycle. After the first 2 minutes, unlatch door, wait 5 seconds, then open door. Check that there is water in the bottom of the dishwasher tub. Check that dishwasher is working properly. REINSTALL ACCESS PANEL 50. Reinstall bent access panel Bent access panel Place the bent access panel against dishwasher legs. 51. Install flat access panel in front of bent panel Place the flat panel in front of the bent panel. Using a Phillips screwdriver install the screws through the holes in the access panel. 20

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
20
1.
Connect rubber end of drain hose
to air gap.
2.
Attach drain hose to air gap. Use a
1" to 1
1
/
2
" (2.5 to 3.8 cm) screw-type
clamp.
3.
Use a rubber hose (not provided) with
screw-type clamps (not provided) to
connect from waste tee to air gap.
Option D: No waste disposer –
with air gap
Large drain
hose clamp
Drain hose
Screw-type clamps
Air gap
Rubber hose
connector
Drain trap
Waste tee
1
Rubber
end
2
3
COMPLETE INSTALLATION
Check that the power supply wire or cord does not touch
dishwasher motor or the lower part of the dishwasher tub.
48.
Power supply cord—Plug into
a grounded 3 prong outlet
Plug into a grounded 3 prong outlet.
49.
Reconnect power
Reconnect electrical power at the fuse box or circuit
breaker box.
NOTE:
With the access panel off, start the dishwasher and allow
it to complete the shortest wash cycle. After the first 2 minutes,
unlatch door, wait 5 seconds, then open door. Check that there is
water in the bottom of the dishwasher tub. Check that dishwasher
is working properly.
REINSTALL ACCESS PANEL
50.
Reinstall bent access panel
Place the bent access panel against dishwasher legs.
51.
Install flat access panel in front of
bent panel
Place the flat panel in front of the bent panel. Using a Phillips
screwdriver install the screws through the holes in the access
panel.
Bent access
panel