Xerox LY8 User Guide - Page 58

Problem, Probable Cause, Remedy, Enabling High Speed Printer, Communications, Pro 16p, Properties

Get Xerox LY8 - WorkCentre Pro 16P B/W Laser Printer PDF manuals and user guides View all Xerox LY8 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 58 highlights

Problem Printing is too slow Irregular faded patches of print Black staining Character voids Background scatter Probable Cause The computer parallel port may not be set for high speed communications. If using Windows 95, the spool setting may be set incorrectly. Print Job too large There is a paper quality problem. Toner may be unevenly distributed. There is a paper quality problem. The paper may be too dry. The paper may be too damp. Printing over uneven surfaces. Remedy If your computer is equipped with an ECP parallel port, enable this mode of operation. Refer to the Enabling High Speed Printer Communications section and your computers user guide. Point to the Start Task bar and then click Settings then Printers. Click the Xerox Document WorkCentre Pro 16p with the right mouse button. Click Properties and then spool settings on the details tab. Select the desired setting from the available choices. Reduce resolution from 600 dpi to 300 dpi. (Refer to Pro 16p Properties (Printer Driver).) Use only paper that meets the specifications required by the printer. Remove the toner cartridge and shake it gently to evenly distribute the toner. Then reinstall the toner cartridge. Use only paper that meets the specifications required by the Pro 16p. Try printing with a different batch of paper. Try printing with a different batch of paper. Do not open packages of paper until necessary so that the paper does not absorb too much moisture from the air. If printing onto envelopes, change your printing layout to avoid printing over areas that have overlapping seams on the reverse side. 52

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
52
Problem
Probable Cause
Remedy
Printing is too slow
The computer parallel port may
not be set for high speed
communications.
If your computer is equipped with
an ECP parallel port, enable this
mode of operation.
Refer to the
Enabling High Speed Printer
Communications
section and
your computers user guide.
If using Windows 95, the spool
setting may be set incorrectly.
Point to the Start Task bar and
then click Settings then Printers.
Click the Xerox Document
WorkCentre Pro 16p with the right
mouse button.
Click Properties
and then spool settings on the
details tab.
Select the desired
setting from the available choices.
Print Job too large
Reduce resolution from 600 dpi to
300 dpi.
(Refer to
Pro 16p
Properties (Printer Driver)
.)
Irregular faded
patches of print
There is a paper quality problem.
Use only paper that meets the
specifications required by the
printer.
Toner may be unevenly
distributed.
Remove the toner cartridge and
shake it gently to evenly distribute
the toner.
Then reinstall the toner
cartridge.
Black staining
There is a paper quality problem.
Use only paper that meets the
specifications required by the Pro
16p.
Character voids
The paper may be too dry.
Try printing with a different batch
of paper.
Background scatter
The paper may be too damp.
Try printing with a different batch
of paper.
Do not open packages
of paper until necessary so that
the paper does not absorb too
much moisture from the air.
Printing over uneven surfaces.
If printing onto envelopes, change
your printing layout to avoid
printing over areas that have
overlapping seams on the reverse
side.