Yamaha CLP-511 Owner's Manual - Page 34

Connecting to a Personal Computer - owner s manual

Get Yamaha CLP-511 PDF manuals and user guides View all Yamaha CLP-511 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

Connecting to a Personal Computer Although the CLP-411/511 can be connected to a personal computer via the MIDI IN/OUT connectors and a MIDI interface, the TO HOST connector and HOST SELECT switch allow direct connection to Apple Macintosh or IBM-PC/AT personal computers for sequencing and other music applications without the need for a separate MIDI interface. HOST SELECT PC-2 PC-1 MIDI Mac TO HOST Set to the "Mac" position. Apple Macintosh Series Computer Connecting to an Apple Macintosh Series Computer ...Connect the TO HOST connector of the Clavinova to the modem or printer port on your Macintosh, depending on which port your MIDI software is using for MIDI data communication, using a standard Macintosh 8-pin system peripheral cable. Set the HOST SELECT switch to the "Mac" position. You may also have to make other MIDI interface settings on the computer side, depending on the type of software you use (refer to your software owner's manual). In any case the clock speed should be set to 1 MHz. q "Mac" Cable Connections MINI DIN 1 8-PIN 2 3 4 5 6 7 8 • 8-pin system peripheral cable. • Data transfer rate: 31,250 bps. 2 (HSK i) 1 (HSK 0) 5 (RxD-) 4 GND 3 (TxD-) 8 (RxD+) 7 (GP i) 6 (TxD+) MINI DIN 8-PIN NOTE • When using the [TO HOST] terminal of the CLP-411/511, first turn the power off on both the CLP-411/511 and the computer before connecting the cable. After connecting the cable, turn the power of the computer on first, then the CLP-411/511. • When not using the [TO HOST] terminal of the CLP-411/511, make sure the cable is disconnected from the [TO HOST] terminal. If the cable is left connected, the CLP-411/511 may not function properly. • When the HOST SELECT switch is set to "Mac", "PC-1", or "PC-2, no data transfer occurs via the MIDI connectors. To use the MIDI connectors for connection via a standard MIDI interface, set the HOST SELECT switch to "MIDI". • If your system doesn't work properly with the connections and settings listed above, your software may require different settings. Check your software operation manual and set the HOST SELECT switch to the position that provides the appropriate data transfer rate. 30

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
30
Connecting to a Personal Computer
Although the CLP-411/511 can be connected to a personal computer via the
MIDI IN/OUT connectors and a MIDI interface, the TO HOST connector and
HOST SELECT switch allow direct connection to Apple Macintosh or IBM-PC/AT
personal computers for sequencing and other music applications without the
need for a separate MIDI interface.
Connect the TO HOST connector of the Clavinova to the modem or
printer port on your Macintosh, depending on which port your MIDI
software is using for MIDI data communication, using a standard
Macintosh 8-pin system peripheral cable. Set the HOST SELECT
switch to the “Mac” position.
You may also have to make other MIDI interface settings on the
computer side, depending on the type of software you use (refer to your
software owner’s manual). In any case the clock speed should be set to
1 MHz.
Connecting to an Apple Macintosh Series
Computer
................................................................................................................
HOST SELECT
TO HOST
PC-2
PC-1
Mac
MIDI
Apple Macintosh
Series Computer
Set to the “Mac”
position.
●
“Mac” Cable Connections
2 (HSK i)
1
1 (HSK 0)
2
5 (RxD-)
3
MINI DIN
8-PIN
4 GND
4
3 (TxD-)
5
8 (RxD+)
6
7 (GP i)
7
6 (TxD+)
8
MINI DIN
8-PIN
•
8-pin system peripheral cable.
•
Data transfer rate: 31,250 bps.
NOTE
•
When using the [TO HOST] terminal of the CLP-411/511, first turn the
power off on both the CLP-411/511 and the computer before connecting
the cable.
After connecting the cable, turn the power of the computer on
first, then the CLP-411/511.
•
When not using the [TO HOST] terminal of the CLP-411/511, make sure
the cable is disconnected from the [TO HOST] terminal.
If the cable is left
connected, the CLP-411/511 may not function properly.
•
When the HOST SELECT switch is set to “Mac”, “PC-1”, or “PC-2, no
data transfer occurs via the MIDI connectors. To use the MIDI connectors
for connection via a standard MIDI interface, set the HOST SELECT
switch to “MIDI”.
•
If your system doesn’t work properly with the connections and settings
listed above, your software may require different settings. Check your
software operation manual and set the HOST SELECT switch to the
position that provides the appropriate data transfer rate.