Yamaha EL-100 Owner's Manual - Page 128

BENCH ASSEMBLY, Connect the AC Power Cord plug to the AC Inlet - review

Get Yamaha EL-100 PDF manuals and user guides View all Yamaha EL-100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 128 highlights

9. Connect the AC Power Cord plug to the AC Inlet of the Main Unit. BENCH ASSEMBLY Reverse the bench board and place one of the legs to the corner of the bench board, then tighten the nut using the included wrench. Be sure to put the washer between the leg and the bench board. leg washer 10.Place the Music Stand. nut bench board 11 11.Turn on the Electone's power switch and confirm that the Electone can be played, or that the assembly is successful. ■ After completing the assembly, please check the following items. • Are there any parts left over? fi Review all assembly procedures. • Is the Electone clear of doors and other movable fixtures? fi Move the Electone to an appropriate location. • Does the Electone make a rattling noise when you shake it? fi Tighten all screws. • Can the Electone be turned on? fi Confirm that the AC power cord plug is securely connected to the Electone's AC Inlet and the other side of the cord is connected to an appropriate power outlet. • Does the Electone produce sounds? fi Confirm that the Speaker cord plug and the Pedalboard cord plug are securely connected to each socket on the Main unit. If the Electone creaks or is otherwise unsteady when you play on the keyboard, refer to the assembly instructions and tighten all screws again. Appendix 128

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
128
Appendix
11
9.
Connect the AC Power Cord plug to the AC Inlet
of the Main Unit.
10
.
Place the Music Stand.
11
.
Turn on the Electone’s power switch and confirm
that the Electone can be played, or that the
assembly is successful.
BENCH ASSEMBLY
Reverse the bench board and place one of the legs to the
corner of the bench board, then tighten the nut using the
included wrench. Be sure to put the washer between the
leg and the bench board.
leg
bench
board
nut
washer
■
After completing the assembly, please check the following
items.
•
Are there any parts left over?
fi
Review all assembly procedures.
•
Is the Electone clear of doors and other movable
fixtures?
fi
Move the Electone to an appropriate location.
•
Does the Electone make a rattling noise when you
shake it?
fi
Tighten all screws.
•
Can the Electone be turned on?
fi
Confirm that the AC power cord plug is securely
connected to the Electone’s AC Inlet and the other
side of the cord is connected to an appropriate power
outlet.
•
Does the Electone produce sounds?
fi
Confirm that the Speaker cord plug and the Pedalboard
cord plug are securely connected to each socket on
the Main unit.
If the Electone creaks or is otherwise unsteady when you
play on the keyboard, refer to the assembly instructions and
tighten all screws again.