Yamaha MOX6 Owner's Manual - Page 60

Appendix Display Messages LCD indication Description All remote templates stored. Appears when you store the Control Template in the Remote mode. Are you sure? Confirms whether you want to execute a specified operation or not. Arpeggio memory full. The internal memory for Arpeggio data is full, preventing storing the recorded sequence data as an Arpeggio. Arpeggio type copied. The Arpeggio Types are copied to the [SF1] - [SF6] buttons. Bad USB device. The USB flash memory device connected to this instrument is unusable. Format the USB flash memory device and try again. Bulk protected. Bulk data cannot be received because of the setting in the Utility mode. Can't undo. OK? When certain Song/Pattern Jobs are executed, internal memory becomes too full for use of the Undo operation. Completed. The specified load, save, format, or other Job has been completed. Device number is off. Bulk data cannot be transmitted/received since the device number is off. Device number mismatch. Bulk data cannot be transmitted/received since the device numbers don't match. Edited data will be discarded. Prompts you to confirm whether or not to erase the edited data. Edits will be stored by loading. Confirms whether or not you want to continue the Load operation. If you select yes, the current edits will be stored. Edits will be stored by saving. Confirms whether or not you want to continue the Save operation. If you select yes, the current edits will be stored. Empty Favorite! Appears when you press the [FAVORITE] button with no program registered to the Favorite Category. [SHIFT]+[FAVORITE] to add. Executing... A format operation or Job is being executed. Please wait. File already exists. A file having the same name as the one you are about to save already exists. File not found. The file of the specified type cannot be found. Folder is too deep. Directories below this level cannot be accessed. Illegal file name. The specified file name is invalid. Try entering a different name. Illegal file. The file specified for loading is unusable by this instrument or cannot be loaded in the current mode. Illegal input. An invalid input or value has been specified. Check the input method or value. Illegal measure. An invalid measure number has been specified in the Song/Pattern mode. Select the measure again. Illegal phrase number. An invalid phrase number has been specified in the Pattern mode. Select the phrase again. Illegal Track number. An invalid Track number has been specified in the Song/Pattern mode. Select the Track again. Incompatible USB device A USB device which cannot be used with this instrument has been connected to the USB [TO DEVICE] terminal. MIDI buffer full. Failed to process the MIDI data because too much data was received at one time. MIDI checksum error. An error occurred when receiving bulk data. MIDI data error. An error occurred when receiving MIDI data. Mixing Voice full. The Mixing Voice cannot be stored because the number of Voices already stored has exceeded the maximum capacity. No data. When a Song/Pattern Job is executed, the selected Track or range contains no data. Select an appropriate Track or range. In addition, this message appears when a Job related to a Mixing Voice cannot be executed because the specified Mixing Voice is not available. No F7 (End of Exc.) Exclusive data has been entered or changed without the necessary "End of Exclusive" byte (F7). Make sure the F7 message is included. No response from USB device There is no response from the USB device connected to the USB [TO DEVICE] terminal. Not empty folder You have attempted to delete a folder that contains data. Now loading... Indicates that a file is being loaded. Now saving... Indicates that a file is being saved. Now working... Canceling the Load/Save operation, after the [EXIT] button has been pressed. Overwrite? A save operation will overwrite data on the USB flash memory device, and this message confirms whether it is OK to continue or not. Part ** is used for Drum Assign. This message appears when the Part switches of all Parts are set to on, and the Drum Assign function uses Part ** for the Drum Part in Performance mode. The ** mark indicates the Part number. Part ** is used for Layer. This message appears when the Part switches of all Parts are set to on, and the Layer function uses Part ** for the Layer Part in the Performance mode. The ** mark indicates the Part number. 60 MOX6/MOX8 Owner's Manual