Zenith DVB312 Operating Guide - Page 24

Troubleshooting - problems

Get Zenith DVB312 - Progressive-Scan Slim Design DVD Player PDF manuals and user guides
UPC - 044642300333
View all Zenith DVB312 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

Troubleshooting Check the following troubleshooting chart for the possible cause of a problem before contacting service. Problem No power. The power is on, but the DVD player does not work. No picture. No sound. The playback picture is poor. The DVD player does not start playback. The remote control does not work properly. Possible Cause The power cord is disconnected. No disc is inserted. The TV is not set to receive DVD signal output. The video cable is not connected securely. The connected TV power is turned off. The equipment connected with the audio cable is not set to receive DVD signal output. The audio cable is not connected securely. The power of the equipment connected with the audio cable is turned off. The Digital Audio Output is set to the wrong position. The disc is dirty. No disc is inserted. An unplayable disc is inserted. The disc is placed upside down. The disc is not placed within the guide. The disc is dirty. A Lock level is set. The remote control is not pointed at the remote sensor of the DVD player. The remote control is too far from the DVD player. There is an obstacle between the remote control and the DVD player. The batteries in the remote control are exhausted. Solution Plug the power cord into the wall power outlet securely. Insert a disc. (Check that the DVD or, audio CD indicator in the display window lights.) Select the appropriate video input source on the TV so the picture from the DVD player appears on the TV screen. Connect the video cable securely. Turn on the TV. Select the correct input source on the audio receiver so you can listen to the sound from the DVD player. Connect the audio cable securely. Turn on the equipment connected with the audio cable. Set the Digital Audio Output to the correct position, then turn on the DVD player again by pressing POWER. Clean the disc. Insert a disc. (Check that the DVD, or audio CD indicator in the DVD display lights.) Insert a playable disc. (Check the disc type, color system, and Regional Code.) Place the disc with the playback side down. Place the disc on the disc tray correctly inside the guide. Clean the disc. Cancel the Rating function or change the rating level. Point the remote control at the remote sensor of the DVD player. Operate the remote control within 23 ft (7 m). Remove the obstacle. Replace the batteries with new ones. 24

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
24
Troubleshooting
Check the following troubleshooting chart for the possible cause of a problem before contacting service.
Problem
No power.
The power is on, but
the DVD player does
not work.
No picture.
No sound.
The playback picture is
poor.
The DVD player does
not start playback.
The remote control
does not work properly.
Possible Cause
z
The power cord is disconnected.
z
No disc is inserted.
z
The TV is not set to receive DVD signal
output.
z
The video cable is not connected
securely.
z
The connected TV power is turned off.
z
The equipment connected with the
audio cable is not set to receive DVD
signal output.
z
The audio cable is not connected
securely.
z
The power of the equipment connected
with the audio cable is turned off.
z
The Digital Audio Output is set to the
wrong position.
z
The disc is dirty.
z
No disc is inserted.
z
An unplayable disc is inserted.
z
The disc is placed upside down.
z
The disc is not placed within the guide.
z
The disc is dirty.
z
A Lock level is set.
z
The remote control is not pointed at the
remote sensor of the DVD player.
z
The remote control is too far from the
DVD player.
z
There is an obstacle between the remote
control and the DVD player.
z
The batteries in the remote control are
exhausted.
Solution
z
Plug the power cord into the wall power
outlet securely.
z
Insert a disc. (Check that the DVD or,
audio CD indicator in the display
window lights.)
z
Select the appropriate video input
source on the TV so the picture from the
DVD player appears on the TV screen.
z
Connect the video cable securely.
z
Turn on the TV.
z
Select the correct input source on the
audio receiver so you can listen to the
sound from the DVD player.
z
Connect the audio cable securely.
z
Turn on the equipment connected with
the audio cable.
z
Set the Digital Audio Output to the
correct position, then turn on the DVD
player again by pressing POWER.
z
Clean the disc.
z
Insert a disc. (Check that the DVD, or
audio CD indicator in the DVD display
lights.)
z
Insert a playable disc. (Check the disc
type, color system, and Regional Code.)
z
Place the disc with the playback side
down.
z
Place the disc on the disc tray correctly
inside the guide.
z
Clean the disc.
z
Cancel the Rating function or change
the rating
level.
z
Point the remote control at the remote
sensor of the DVD player.
z
Operate the remote control within 23 ft
(7 m).
z
Remove the obstacle.
z
Replace the batteries with new ones.