Adaptec 29320LPE User Guide - Page 29

Installing with Red Hat Linux, Installing with NetWare, For SLES 9.0, Alt key, Manual install mode - scsi driver

Get Adaptec 29320LPE - SCSI Card Storage Controller U320 320 MBps PDF manuals and user guides
UPC - 760884154762
View all Adaptec 29320LPE manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

Chapter 6: Installing the Driver and an Operating System ● 29 Installing with Red Hat Linux To install the SCSI card driver while installing Red Hat Linux: Note: For the most up-to-date information on Linux support, visit www.adaptec.com. 1 Insert the first Red Hat installation CD. 2 Restart the system. 3 When the Red Hat Welcome screen appears, type linux dd at the Boot: prompt. 4 When prompted, insert the driver disk, then select OK. 5 Follow the prompts to set up the environment you want. 6 If you are installing other third-party devices, install them now. Otherwise, select Done. 7 Continue with the Linux installation, according to the Red Hat instructions. Installing with SUSE Linux To install the SCSI card driver while installing SUSE Linux: Note: For the most up-to-date information on Linux support, visit www.adaptec.com. 1 Insert the first SUSE Installation CD. 2 Restart your system. 3 When the SUSE installation selection screen appears, choose the type of installation you want, then ... For SLES 9.0: Press the F6 key to indicate the use of a driver disk. (If F6 is not shown on the screen, you may have an older version of SUSE; press the Alt key instead.) For SLES 10.0: Press the F5 key and select Yes to indicate the use of a driver disk. 4 When prompted, insert the driver disk, then press any key to continue. 5 Follow the prompts to set up the environment you want. 6 If you are installing other third-party devices, install them now. Otherwise, select Back. 7 Complete the Linux installation, following the instructions included with your operating system. Installing with NetWare To install the SCSI card driver while installing NetWare: 1 Restart your system, then install NetWare. (For instructions, refer to your NetWare documentation). 2 To be able to load additional drivers later, select Manual install mode during the first part of the installation. 3 When the Device Drivers screen displays, check the storage adapters list, then select Modify to add another driver. 4 Select Storage Adapters, then press Enter.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
Chapter 6: Installing the Driver and an Operating System
●
29
Installing with Red Hat Linux
To install the SCSI card driver while installing Red Hat Linux:
Note:
For the most up-to-date information on Linux support, visit www.adaptec.com.
1
Insert the first Red Hat installation CD.
2
Restart the system.
3
When the Red Hat Welcome screen appears, type
linux dd
at the Boot: prompt.
4
When prompted, insert the driver disk, then select
OK
.
5
Follow the prompts to set up the environment you want.
6
If you are installing other third-party devices, install them now. Otherwise, select
Done
.
7
Continue with the Linux installation, according to the Red Hat instructions.
Installing with SUSE Linux
To install the SCSI card driver while installing SUSE Linux:
Note:
For the most up-to-date information on Linux support, visit www.adaptec.com.
1
Insert the first SUSE Installation CD.
2
Restart your system.
3
When the SUSE installation selection screen appears, choose the type of installation you
want, then ...
For SLES 9.0
: Press the
F6
key to indicate the use of a driver disk. (If
F6
is not shown on the
screen, you may have an older version of SUSE; press the
Alt key
instead.)
For SLES 10.0
: Press the
F5
key and select
Yes
to indicate the use of a driver disk.
4
When prompted, insert the driver disk, then press any key to continue.
5
Follow the prompts to set up the environment you want.
6
If you are installing other third-party devices, install them now. Otherwise, select
Back
.
7
Complete the Linux installation, following the instructions included with your operating
system.
Installing with NetWare
To install the SCSI card driver while installing NetWare:
1
Restart your system, then install NetWare. (For instructions, refer to your NetWare
documentation).
2
To be able to load additional drivers later, select
Manual install mode
during the first part
of the installation.
3
When the Device Drivers screen displays, check the storage adapters list, then select
Modify
to add another driver.
4
Select
Storage Adapters
, then press
Enter
.